Influence of load cycle asymmetry and overloading on fatigue crack growth rate in stainless steels

1986 ◽  
Vol 22 (3) ◽  
pp. 258-262 ◽  
Author(s):  
A. A. Popov ◽  
E. I. Mamaeva ◽  
G. A. Drobakhin ◽  
T. K. Kashirina
Keyword(s):  
Growth Rate ◽  
Fatigue Crack ◽  
Crack Growth Rate ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Fatigue Crack Growth Rate ◽  
Stainless Steels ◽  
Load Cycle ◽  
Cycle Asymmetry

Effect of sea salt on fatigue crack growth rate in stainless steels and VT3-1 alloy

1981 ◽  
Vol 13 (4) ◽  
pp. 477-481 ◽  
Author(s):  
V. T. Troshchenko ◽  
A. V. Prokopenko ◽  
V. N. Torgov
Keyword(s):  
Growth Rate ◽  
Fatigue Crack ◽  
Crack Growth Rate ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Fatigue Crack Growth Rate ◽  
Stainless Steels ◽  
Sea Salt

Fatigue Crack Growth Curve for Austenitic Stainless Steels in BWR Environment

2000 ◽  
Vol 123 (2) ◽  
pp. 166-172 ◽  
Author(s):  
M. Itatani ◽  
M. Asano ◽  
M. Kikuchi ◽  
S. Suzuki ◽  
K. Iida,
Keyword(s):  
Growth Rate ◽  
Fatigue Crack ◽  
Crack Growth Rate ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Fatigue Crack Growth Rate ◽  
Stainless Steels ◽  
Stress Ratio ◽  
Austenitic Stainless Steels ◽  
Reference Curve

Fatigue crack growth data obtained in the simulated BWR water environment were analyzed to establish a formula for reference fatigue crack growth rate (FCGR) of austenitic stainless steels in BWR water. The effects of material, mechanical and environmental factors were taken into the reference curve, which was expressed as: da/dN=8.17×10−12s˙Tr0.5s˙ΔK3.0/1−R2.121≦ΔK≦50 MPam where da/dN is fatigue crack growth rate in m/cycle, Tr is load rising time in seconds, ΔK is range (double amplitude) of K–value in MPam, and R is stress ratio. Tr=1 s if Tr<1 s, and Tr=1000 s if Tr cannot be defined. ΔK=Kmax−Kmin if R≧0.ΔK=Kmax if R<0.R=Kmin/Kmax. The proposed formula provides conservative FCGR at low stress ratio. Although only a few data show higher FCGR than that by proposed formula at high R, these data are located in a wide scatter range of FCGR and are regarded to be invalid. The proposed formula is going to be introduced in the Japanese Plant Operation and Maintenance Standard.

Fatigue Crack Growth Curve for Austenitic Stainless Steels in PWR Environment

2006 ◽  
Author(s):  
Yuichiro Nomura ◽  
Katsumi Sakaguchi ◽  
Hiroshi Kanasaki ◽  
Shigeki Suzuki
Keyword(s):  
Growth Rate ◽  
Fatigue Crack ◽  
Crack Growth Rate ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Fatigue Crack Growth Rate ◽  
Growth Curve ◽  
Stainless Steels ◽  
Austenitic Stainless Steels ◽  
Crack Growth Curve

Reference fatigue crack growth rate curves for austenitic stainless steels in pressurized water reactors (PWR) environments were prescribed in JSME S NA1-2004(1) in Japan. The reference fatigue crack growth curve in PWR environment had been determined as a function of stress intensity factor range, temperature, load rising time and stress ratio. In order to confirm the applicability of the reference fatigue crack growth rate curve under high stress ratio, low rising time and low stress intensity range, fatigue crack propagation tests of austenitic stainless steels 316, 316 weld metal, 304 and 304 weld metal were carried out. It is concluded that the reference fatigue crack growth curve in PWR environment is applicable to predict fatigue crack growth rate of this study test conditions.

Dependence of fatigue crack growth rate on cycle asymmetry

1987 ◽  
Vol 19 (3) ◽  
pp. 284-287
Author(s):  
V. I. Trufyakov ◽  
V. V. Knysh ◽  
P. P. Mikheev ◽  
A. Z. Kuz'menko
Keyword(s):  
Growth Rate ◽  
Fatigue Crack ◽  
Crack Growth Rate ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Fatigue Crack Growth Rate ◽  
Cycle Asymmetry
Sign in / Sign up

Export Citation Format

Share Document