Novel Method for Refining Coarse Eutectic Carbides in Ultrahigh-Carbon Steel

2020 ◽  
Vol 61 (9-10) ◽  
pp. 543-546
Author(s):  
Qingsuo Liu ◽  
Fang Wang ◽  
Xin Zhang ◽  
Huibin Wang ◽  
Jinman Li
Keyword(s):  
Carbon Steel ◽  
Eutectic Carbides ◽  
Ultrahigh Carbon Steel ◽  
Novel Method

Factors Influencing the Fatigue Behavior of Ferrous Laminates

1987 ◽  
Vol 109 (3) ◽  
pp. 244-251 ◽  
Author(s):  
J. Wittenauer ◽  
O. D. Sherby
Keyword(s):  
Fatigue Crack ◽  
Fatigue Life ◽  
Carbon Steel ◽  
Fatigue Behavior ◽  
Layered Material ◽  
Factors Influencing ◽  
Ultrahigh Carbon Steel ◽  
Processing History ◽  
Crack Blunting ◽  
Similar Processing

Laminates based on ultrahigh carbon steel were prepared and found to exhibit enhanced fatigue life as compared to a monolithic reference material. This result was achieved through the insertion of weak interlaminar regions of copper into the layered material during preparation of the laminates. The presence of these regions allowed for the operation of a delamination mechanism in advance of the propagating fatigue crack. The result was interlaminar separation and associated crack blunting. Stress-life curves show that an increase in life by as much as a factor of four is achieved for these materials when compared to monolithic specimens of similar processing history.

Influence of Cooling Rate on the Microstructure in HCCI/Steel Bimetal Composite Hammer

2012 ◽  
Vol 538-541 ◽  
pp. 1041-1044 ◽  
Author(s):  
Ning Wei ◽  
Kai Wang ◽  
Xiang Kui Zhou ◽  
Qiang Wang ◽  
Qiang Liu ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Cooling Rate ◽  
Mold Material ◽  
Eutectic Carbides ◽  
Fast Cooling ◽  
Primary Carbides ◽  
Bimetal Composite

The HCCI/carbon steel bimetal composite hammer was prepared by bimetal liquid cast process and the effect of cooling rate, which is obtained by different mold material, on the microstructures of hypereutectic HCCI was studied. The results show that the primary carbides and eutectic carbides are refined with the increase of cooling rate. Good metallurgical combination of the HCCI/carbon steel bimetal hammer can be reached by bimetal liquid cast process with fast cooling mold.

A Germanic ultrahigh carbon steel punch of the Late Roman-Iron Age

2004 ◽  
Vol 31 (8) ◽  
pp. 1117-1125 ◽  
Author(s):  
Evelyne Godfrey ◽  
Matthijs van Nie
Keyword(s):  
Carbon Steel ◽  
Iron Age ◽  
Ultrahigh Carbon Steel ◽  
Late Roman

The fracture toughness of a ultrahigh carbon steel containing 1.5 wt% C

2006 ◽  
Vol 29 (9-10) ◽  
pp. 817-828 ◽  
Author(s):  
A. FERNANDEZ-VICENTE ◽  
M. CARSI ◽  
F. PENALBA ◽  
O. A. RUANO
Keyword(s):  
Fracture Toughness ◽  
Carbon Steel ◽  
Ultrahigh Carbon Steel

scholarly journals Superplasticity in Ultrahigh Carbon Steel

1984 ◽  
Vol 70 (8) ◽  
pp. 767-773 ◽  
Author(s):  
Masaharu TOKIZANE ◽  
Toshimasa OYAMA
Keyword(s):  
Carbon Steel ◽  
Ultrahigh Carbon Steel

Deformation behavior during hot torsion of an ultrahigh carbon steel containing 1.3 wt.% C

2003 ◽  
Vol 94 (8) ◽  
pp. 922-929 ◽  
Author(s):  
A. Fernández–Vicente ◽  
M. Carsí ◽  
F. Peñalba ◽  
F. Carreño ◽  
O. A. Ruano
Keyword(s):  
Carbon Steel ◽  
Deformation Behavior ◽  
Ultrahigh Carbon Steel ◽  
Hot Torsion

Processing, structure, and properties of a rolled, ultrahigh-carbon steel plate exhibiting a damask pattern

2001 ◽  
Vol 46 (1) ◽  
pp. 11-18 ◽  
Author(s):  
Eric M Taleff ◽  
Bruce L Bramfitt ◽  
Chol K Syn ◽  
Donald R Lesuer ◽  
Jeffrey Wadsworth ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Steel Plate ◽  
Structure And Properties ◽  
Ultrahigh Carbon Steel

scholarly journals High Strain Rate - High Strain Response of an Ultrahigh Carbon Steel Containing 1.3% C and 3% Si

2003 ◽  
Vol 426-432 ◽  
pp. 841-846 ◽  
Author(s):  
Donald R. Lesueur ◽  
C.K. Syn ◽  
Oleg D. Sherby ◽  
Dong Wha Kum
Keyword(s):  
Carbon Steel ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Strain Response ◽  
Ultrahigh Carbon Steel
Sign in / Sign up

Export Citation Format

Share Document