The Joint Effects of Nitriding and Parameters Related to the Destabilisation of Austenite on Wear Resistance in White Cast Iron with 25% Cr

In this article, the effects of an ionic nitriding treatment are analysed, together with deliberate variation of different thermal parameters associated with the destabilisation of austenite, on erosive wear resistance of white cast irons with 25% Cr. The methodology followed in this research was an experimental design, where six factors were analyzed by performing eight experiments. The thickness of the nitrided layer is much smaller than in white cast iron with lower percentages in Cr, never reaching 20 microns. The nitriding treatment entails considerable softening of the material underneath the nitriding layer. This softening behaviour becomes partially inhibited when the destabilisation temperature of austenite is 1100 °C and dwell times at such temperature are prolonged. This temperature seems to play a significant role in the solubilization of non-equilibrium eutectic carbides, formed during industrial solidification. The nitriding treatment leads to additional hardening, which, in these cases, favours a second destabilisation of austenite, with additional precipitation of secondary carbides and the transformation of retained austenite into martensite. Despite softening of the material, the nitriding treatment, together with air-cooling after destabilisation of the austenite, allows a noticeable increase in resistance to erosive wear.

Cyclic annealing versus continuous annealing of 20 wt.% chromium white cast iron

To destabilize as-cast microstructure of 20 wt.% chromium white iron, cyclic annealing involving repeated austenitization for short duration of 0.6 h at 900, 950, 1000, 1050 and 1100 °C followed by forced air cooling is conducted as an alternative to continuous annealing requiring austenitization for longer period of 4–6 h at the said temperatures followed by furnace cooling. Continuous austenitization destabilizes the austenite matrix through precipitation of secondary carbides and transforms the alloy depleted austenite to pearlite on furnace cooling, thereby reducing the as-cast hardness from HV 669 to HV466. In contrast, repeated austenitization not only destabilizes the austenite matrix through precipitation of secondary carbides followed by its transformation to martensite on forced air cooling, but also causes disintegration of longer eutectic carbides to shorter segments with subsequent increase in hardness to as high as HV 890. Notched impact toughness after both continuous and cyclic annealing remains uniformly at 12.0 J as compared to as-cast value of 6.0 J. Besides, an unexpected rise in abrasive wear resistance after cyclic annealing treatment makes the alloy superior than that obtained by continuous annealing treatment as practiced in industries.

Influence of Thermal Processing Factors, Linked to the Destabilisation of Austenite, on the Microstructural Variation of a White Cast Iron Containing 25% Cr and 0.6% Mo

Hypoeutectic white cast irons containing 25% Cr are used in ore-processing industries due to their high resistance to erosive wear. Applying a Design of Experiments (DoE), the aim of this study is to analyse the influence of thermal processing factors on the microstructural variation of a white cast iron containing 25% Cr and 0.6% Mo. The carbides present in the as-cast state are of the M7C3, M2C, and M3C types. M2C carbides precipitate on the eutectic M7C3 carbides favoured by heterogeneous nucleation conditions. Two kinetics compete during the destabilisation of austenite. One dissolves those eutectic carbides precipitated as a result of non-equilibrium solidification (M7C3 and M2C), while the other enables the precipitation of secondary M7C3 and M23C6 carbides. The M7C3 carbides begin to precipitate first. Low destabilisation temperatures and short dwell times are insufficient to dissolve the precipitated eutectic carbides from non-equilibrium conditions, thus favouring the presence of M2C carbides, which are associated with Mo. The factor that has the greatest influence on hardness is the tempering temperature. The optimal tempering temperature is found to be 500 °C. Short tempering times maintain the distortion of the ferrite unit cell. The precipitation of Cr carbides during tempering requires a temperature of 500 °C and the prior dissolution of the carbon precipitated during the initial stages of said tempering. With short tempering times, the Cr atoms still remain dissolved in the ferrite, distorting its unit cell and increasing the hardness of the matrix constituent of the alloy.

Influence of Ni Content on Erosive Wear and Destabilization Heat Treatment Conditions Behavior of Multi Component White Cast Iron

This study investigated the influence of nickel (Ni) addition on erosive wear property of multi-component white cast iron with good erosive wear resistance. Multi-component white cast irons (MWCIs) with 2 mass % of carbon (C), 5 mass % of chromium (Cr), molybdenum (Mo), tungsten (W), niobium (Nb) and 0, 3, 5 mass % of Ni were prepared as experimental materials. The heat treatment condition was quenching by forced air cooling after keeping the specimens at 1123K for 3.6ks. Specimens with size of 50mm×50mm×10mm were tested using a suction-type blasting machine. The test was conducted with impact angle of 30, 60 and 90 deg. at room temperature. Collision particles were irregular steel grids with average particle diameter of 770μm and hardness of 810HV1. The speed of air flow was about 100m/s while the speed of impact particles was around 20.0g/s and the total time of each experiment was 3600 sec.. According to the result, erosion rate was decreased with the increase of Ni content in all of the impact angles. Especially, MWCIs which contain 5 mass % Ni showed the most excellent erosive wear resistance. As reasons, it can be considered that with Ni addition, the volume fraction of eutectic carbides and secondary carbides was increased which enhanced the matrix structure and suppressed the surface deformation of the experimental surface. Therefore, the increasing of eutectic carbides and secondary carbides can be considered as the reason of erosive wear resistance increased.

Optimization of Thermal Processes Applied to Hypoeutectic White Cast Iron containing 25% Cr Aimed at Increasing Erosive Wear Resistance

Hypoeutectic white cast irons containing 25% Cr are used in very demanding environments that require high resistance to erosive wear, for instance, the crushing and processing of minerals or the manufacture of cement. This high percentage in Cr, in turn, favors corrosion resistance. The application of a Design of Experiments (DoE) allows the analysis of the effects of modifying certain factors related to the heat treatments applied to these alloys. Among these factors, the influence of prior softening treatment to facilitate the machining of these cast irons and the influence of the factors related to the destabilization of austenite, during both quenching and tempering, were analyzed. The precipitated phases were identified by X-ray diffraction (XRD), while the Rietveld structural refinement method was used to determine their percentages by weight. Erosive wear resistance was calculated using the ASTM G76 standard test method. It is concluded that the thermal softening treatment, consisting of 2 h at 1000 °C and 24 h at 700 °C, does not result in additional softening of the material compared to its as-cast state. Furthermore, it is observed that not only eutectic carbides influence wear resistance, but that the influence of the matrix constituent is also significant. It is also verified that the tempering treatment plays a decisive role in wear resistance. Temperatures of 500 °C and tempering times of 6 h increase the wear resistance and hardness of the aforementioned matrix constituent. Tempering temperatures of 200 °C lead to an increase in retained austenite content and the presence of M3C carbides versus mixed M7C3 and M23C6 carbides. The quench cooling medium is not found to have a significant influence on the hardness or wear resistance.