Wear behaviour and microstructure of laser-processed low carbon steel with chromium

Wear ◽  
1991 ◽  
Vol 145 (1) ◽  
pp. 43-60 ◽  
Author(s):  
Tan Yen-Hung ◽  
Doong Ji-Liang
Keyword(s):  
Carbon Steel ◽  
Low Carbon Steel ◽  
Wear Behaviour ◽  
Low Carbon

An evaluation of the wear behaviour of a dual-phase low-carbon steel

Wear ◽  
1996 ◽  
Vol 193 (2) ◽  
pp. 248-252 ◽  
Author(s):  
M. Aksoy ◽  
M.B. Karamiş ◽  
E. Evin
Keyword(s):  
Carbon Steel ◽  
Low Carbon Steel ◽  
Wear Behaviour ◽  
Dual Phase ◽  
Low Carbon

Dry Sliding Wear Behaviour of Full Pearlite Obtained by Cladding Low Carbon Steel to Hypoeutectoid Steel

2014 ◽  
Vol 1017 ◽  
pp. 147-153
Author(s):  
Xing Jian Gao ◽  
Zheng Yi Jiang ◽  
Dong Bin Wei ◽  
Bu Yung Kosasih ◽  
Si Hai Jiao ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Sliding Wear ◽  
Low Carbon Steel ◽  
Interlamellar Spacing ◽  
Wear Behaviour ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Low Carbon ◽  
Sliding Wear Behaviour ◽  
Hypoeutectoid Steel

The dry sliding wear behaviour of the full pearlite in a novel bimetal consisting of low carbon steel and hypoeutectoid steel has been studied by means of pin-on-disc type wear tests at room temperature. Thermomechanical treatments were performed on the bimetallic samples to obtain different interlamellar spacings. It was found that interlamellar spacing decreased with an increase in plastic strain to a great extent initially and followed by a lower extent of decrease. This decrease not only increases the hardness and strain hardening capacity of the fully pearlitic microstructure, but also is in favor of stabilizing the friction coefficient during sliding process. The observations of wear tracks show that delamination dominated the wear process when interlamellar spacing is higher than 200 nm, while pronounced oxidational wear occurred with interlamellar spacing below 200 nm.

Wear behaviour of low carbon steel after severe shot peening

2013 ◽  
Vol 17 (7) ◽  
pp. 519-523 ◽  
Author(s):  
O. Unal ◽  
R. Varol ◽  
A. Erdogan ◽  
M. S. Gok
Keyword(s):  
Carbon Steel ◽  
Shot Peening ◽  
Low Carbon Steel ◽  
Wear Behaviour ◽  
Low Carbon ◽  
Severe Shot Peening

Development of trimming technology for hot rolled ultra-low carbon steel

1993 ◽  
Vol 90 (7-8) ◽  
pp. 917-922
Author(s):  
Y. Matsuda ◽  
M. Nishino ◽  
J. Ikeda
Keyword(s):  
Carbon Steel ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Ultra Low Carbon Steel ◽  
Hot Rolled

The Effect of Small Defects on Fatigue Life of a Low Carbon Steel

2019 ◽  
Author(s):  
Natalia Gonçalves Torres ◽  
Vinícius Rodrigues ◽  
Edgar Mamiya
Keyword(s):  
Fatigue Life ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
Low Carbon
Sign in / Sign up

Export Citation Format

Share Document