Engineering a 3D Collective Cancer Invasion Model with Control over Collagen Fiber Alignment

The glenohumeral joint is frequently dislocated causing injury to the glenohumeral capsule (axillary pouch (AP), anterior band of the inferior glenohumeral ligament (AB-IGHL), posterior band of the inferior glenohumeral ligament (PB-IGHL), posterior (Post), and anterosuperior region (AS)). [1, 2] The capsule is a passive stabilizer to the glenohumeral joint and primarily functions to resist dislocation during extreme ranges of motion. [3] When unloaded, the capsule consists of randomly oriented collagen fibers, which play a pertinent role in its function to resist loading in multiple directions. [4] The location of failure in only the axillary pouch has been shown to correspond with the highest degree of collagen fiber orientation and maximum principle strain just prior to failure. [4, 5] However, several discrepancies were found when comparing the collagen fiber alignment between the AB-IGHL, AP, and PB-IGHL. [3,6,7] Therefore, the objective was to determine the collagen fiber alignment and maximum principal strain in five regions of the capsule during uniaxial extension to failure and to determine if these parameters could predict the location of tissue failure. Since the capsule functions as a continuous sheet, we hypothesized that maximum principal strain and peak collagen fiber alignment would correspond with the location of tissue failure in all regions of the glenohumeral capsule.

Download Full-text

Rapid Quantification of 3D Collagen Fiber Alignment and Fiber Intersection Correlations with High Sensitivity

PLoS ONE ◽

10.1371/journal.pone.0131814 ◽

2015 ◽

Vol 10 (7) ◽

pp. e0131814 ◽

Cited By ~ 19

Author(s):

Meng Sun ◽

Alexander B. Bloom ◽

Muhammad H. Zaman

Keyword(s):

Collagen Fiber ◽

High Sensitivity ◽

Fiber Alignment ◽

3D Collagen ◽

Collagen Fiber Alignment ◽

Rapid Quantification

Download Full-text

Effect of Preconditioning on Collagen Fiber Recruitment: Inhomogeneous Properties of Rat Supraspinatus Tendon

ASME 2010 Summer Bioengineering Conference, Parts A and B ◽

10.1115/sbc2010-19089 ◽

2010 ◽

Author(s):

Kristin S. Miller ◽

Lena Edelstein ◽

Louis J. Soslowsky

Keyword(s):

Mechanical Properties ◽

Collagen Fiber ◽

Insertion Site ◽

Supraspinatus Tendon ◽

Fiber Alignment ◽

Rigorous Evaluation ◽

Structural Alterations ◽

Testing Protocol ◽

Inhomogeneous Properties ◽

Collagen Fiber Alignment

Cyclic preconditioning is a commonly accepted initial component of any tendon testing protocol. Preconditioning provides tendons with a consistent “history” and stress-strain results become repeatable allowing for rigorous evaluation and comparison. While it is widely accepted that preconditioning is important, changes that occur during preconditioning are not well understood. Micro-structural alterations, such as re-arrangement of collagen fibers, is one proposed mechanism of preconditioning [1,4]. However, this mechanism has not been examined. Therefore, the objective of this study is to locally measure: 1) fiber re-alignment during preconditioning, stress relaxation and tensile testing and 2) corresponding mechanical properties, to address mechanisms of preconditioning as well as tissue nonlinearity and inhomogeneity in the rat supraspinatus tendon. We hypothesize that 1) fiber re-alignment will be greatest in the toe region, but will also occur during preconditioning and 2) mechanical properties and initial collagen fiber alignment will be greater in the midsubstance location of the tendon compared to the tendon-to-bone insertion site.

Download Full-text

Collagen Fiber Re-Alignment and Mechanical Properties in a Mouse Supraspinatus Tendon Model: Examining Changes With Age and Location

ASME 2012 Summer Bioengineering Conference, Parts A and B ◽

10.1115/sbc2012-80017 ◽

2012 ◽

Cited By ~ 1

Author(s):

Kristin S. Miller ◽

Brianne K. Connizzo ◽

Elizabeth Feeney ◽

Louis J. Soslowsky

Keyword(s):

Mechanical Properties ◽

Collagen Fiber ◽

Mechanical Load ◽

Mechanical Test ◽

Insertion Site ◽

Supraspinatus Tendon ◽

Tissue Response ◽

Mechanical Stimuli ◽

Fiber Alignment ◽

Collagen Fiber Alignment

One postulated mechanism of tendon structural response to mechanical load is collagen fiber re-alignment. Recently, where collagen fiber re-alignment occurs during a tensile mechanical test has been shown to vary by tendon age and location in a postnatal developmental mouse supraspinatus tendon (SST) model [1]. It is thought that as the tendon matures and its collagen fibril network, collagen cross-links and collagen-matrix interactions develop, its ability to respond quickly to mechanical stimuli hastens [1]. Additionally, the insertion site and midsubstance of postnatal SST may develop differently and at different rates, providing a potential explanation for differences in fiber re-alignment behaviors at the insertion site and midsubstance at postnatal developmental time points [1]. However, collagen fiber re-alignment behavior, in response to mechanical load at a mature age and in comparison to developmental ages, have not been examined. Therefore, the objectives of this study are to locally measure: 1) fiber re-alignment during preconditioning and tensile mechanical testing and 2) to compare local differences in collagen fiber alignment and corresponding mechanical properties to address tissue response to mechanical load in the mature and postnatal developmental mouse SST. We hypothesize that 1) 90 day tendons will demonstrate the largest shift in fiber re-alignment during preconditioning, but will also re-align during the toe- and linear-regions. Additionally, we hypothesize that 2) mechanical properties and initial collagen fiber alignment will be greater in the midsubstance of the tendon compared to the tendon-to-bone insertion site at 90 days, 3) that mechanical properties will increase with age, and that 4) collagen fiber organization at the insertion site will decrease with age.

Download Full-text