Finite element modelling and experimental validation of a total implanted shoulder joint

2021 ◽  
pp. 106254
Author(s):  
M. Bola ◽  
J.A. Simões ◽  
A. Ramos
Keyword(s):  
Finite Element ◽  
Shoulder Joint ◽  
Finite Element Modelling ◽  
Experimental Validation ◽  
Element Modelling

scholarly journals Experimental validation of finite element modelling on tibia with osteogenesis imperfecta

2019 ◽  
Vol 670 ◽  
pp. 012015
Author(s):  
H Y Tan ◽  
K S Basaruddin ◽  
S F Khan ◽  
M H Mat Som ◽  
R Daud ◽  
...  
Keyword(s):  
Finite Element ◽  
Osteogenesis Imperfecta ◽  
Finite Element Modelling ◽  
Experimental Validation ◽  
Element Modelling

Finite element modelling and experimental validation of bolt loosening due to thread wear under transverse cyclic loading

2019 ◽  
Vol 104 ◽  
pp. 341-353 ◽  
Author(s):  
Mingyuan Zhang ◽  
Dongfang Zeng ◽  
Liantao Lu ◽  
Yuanbin Zhang ◽  
Jing Wang ◽  
...  
Keyword(s):  
Finite Element ◽  
Cyclic Loading ◽  
Finite Element Modelling ◽  
Experimental Validation ◽  
Element Modelling ◽  
Bolt Loosening

scholarly journals Dimpling process in cold roll metal forming by finite element modelling and experimental validation

2014 ◽  
Vol 16 (3) ◽  
pp. 363-372 ◽  
Author(s):  
V.B. Nguyen ◽  
C.J. Wang ◽  
D.J. Mynors ◽  
M.A. English ◽  
M.A. Castellucci
Keyword(s):  
Finite Element ◽  
Metal Forming ◽  
Finite Element Modelling ◽  
Experimental Validation ◽  
Element Modelling ◽  
Cold Roll

scholarly journals Inherent possibilities and limitations of finite element modelling of defective girth welds

2010 ◽  
Vol 1 (1) ◽  
pp. 127-135
Author(s):  
Stijn Hertele ◽  
Wim De Waele ◽  
Rudi Denys ◽  
Matthias Verstraete
Keyword(s):  
Finite Element ◽  
Crack Growth ◽  
Experimental Research ◽  
Finite Element Modelling ◽  
Experimental Validation ◽  
Stable Crack Growth ◽  
Worst Case ◽  
Element Modelling ◽  
Numerical Research ◽  
Girth Welds

Welds unavoidably show defects, which can negatively affect the integrity of the entire structureand, worst case, result in a failure. Defects of a considerable size should therefore be detected, assessedand, if necessary, repaired. The assessment of a defect requires a procedure which allows a conservativeestimation of the acceptability of the defect. To develop such procedure, both experimental and numericalresearch is performed. This paper describes the inherent possibilities and limitations of numerical researchthrough finite element modelling, as compared to experimental research. Summarizing all arguments, itbecomes clear that numerical research is a highly powerful tool, but a thorough experimental validation is ofparamount importance. Moreover, some specific weld-related problems are highly difficult to address,namely the presence of stable crack growth and material heterogeneity. More research is needed toachieve a description of these phenomena, under a set of conservative assumptions.

Comparison of geometry-based and CT voxel-based finite element modelling and experimental validation

1998 ◽  
Vol 20 (7) ◽  
pp. 515-522 ◽  
Author(s):  
M Lengsfeld ◽  
J Schmitt ◽  
P Alter ◽  
J Kaminsky ◽  
R Leppek
Keyword(s):  
Finite Element ◽  
Finite Element Modelling ◽  
Experimental Validation ◽  
Element Modelling

scholarly journals Finite Element Modelling and Experimental Validation of the Enamel Demineralisation Process at the Rod Level

2020 ◽  
Author(s):  
Enrico Salvati ◽  
Cyril Besnard ◽  
Robert A. Harper ◽  
Thomas Moxham ◽  
Richard M. Shelton ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Modelling ◽  
Experimental Validation ◽  
Element Modelling
Sign in / Sign up

Export Citation Format

Share Document