Quantitative functional evaluation of a 3D–printed silicone-embedded prosthesis for partial hand amputation: A case report

2018 ◽  
Vol 31 (1) ◽  
pp. 129-136 ◽  
Author(s):  
Pilar Alvial ◽  
Gabriela Bravo ◽  
María Paz Bustos ◽  
Gabriel Moreno ◽  
Roberto Alfaro ◽  
...  
Keyword(s):  
Case Report ◽  
Functional Evaluation ◽  
3D Printed ◽  
Hand Amputation

scholarly journals Surgical Wound Mucormycosis Necessitating Hand Amputation: A Case Report

2008 ◽  
Vol 16 (2) ◽  
pp. 267-269 ◽  
Author(s):  
HH Chew ◽  
A Abuzeid ◽  
D Singh ◽  
CC Tai
Keyword(s):  
Case Report ◽  
Surgical Wound ◽  
Hand Amputation

Total ulna replacement with a 3D-printed custom-made prosthesis after en bloc tumor resection: A case report

2018 ◽  
Vol 66 (2) ◽  
pp. e27522 ◽  
Author(s):  
Xiang Fang ◽  
Wenli Zhang ◽  
Zeping Yu ◽  
Hongyuan Liu ◽  
Yan Xiong ◽  
...  
Keyword(s):  
Case Report ◽  
Tumor Resection ◽  
En Bloc ◽  
Custom Made ◽  
3D Printed

Virtual surgical planning and 3D-printed guided biopsy of bilateral lesions in the mandible: a case report

2020 ◽  
Vol 4 (4) ◽  
pp. 185-192
Author(s):  
Douglas Rangel Goulart ◽  
Lucas Raineri Capeletti ◽  
Gabriel Henrique Campos Pinheiro ◽  
Mateus Veppo dos Santos ◽  
Alessandro Lourenço Januario
Keyword(s):  
Case Report ◽  
Surgical Procedure ◽  
Surgical Planning ◽  
Inferior Alveolar Nerve ◽  
Postoperative Recovery ◽  
Virtual Surgical Planning ◽  
Drill Guide ◽  
Bone Biopsies ◽  
3D Printed ◽  
Bilateral Lesions

Purpose: To report the use of virtual surgical planning and a 3D printed drill guide for the biopsy of mandibular lesions. Case report: A 38-year-old woman presented with two bilateral lesions in the mandibular body, in close proximity to the inferior alveolar nerve and the molar roots. An incisional biopsy was planned with coDiagnostiX software using the cone beam computed tomography DICOM files and a cast model that had been digitalized using a bench scanner (7series, Dental Wings, Quebec, Canada). A tooth-supported drill guide was produced by 3D printing with digital light processing technology (Moonray S, Sprintray, CA, USA). The surgical procedure was performed under local anesthesia. No complications were observed intraoperatively or during postoperative recovery. Conclusion: The use of an intraoperative surgical 3D-printed drill guide enables a smaller surgical procedure and more precise bone biopsies.

The application of 3D printed self-glazed zirconia for full-mouth rehabilitation in a patient with severely worn dentition: a case report

2019 ◽  
Vol 119 (5-6) ◽  
pp. 305-311
Author(s):  
Zhu Huang ◽  
Jiangyong Huang ◽  
Chanxiu Li ◽  
Andi Shi ◽  
Jingwen Wu ◽  
...  
Keyword(s):  
Case Report ◽  
Full Mouth Rehabilitation ◽  
3D Printed

Poster 484 3D Printed Orthotic Designed for Klippel-Feil Syndrome Affected Hypoplastic Thumb: A Case Report

PM&R ◽  
2016 ◽  
Vol 8 (9) ◽  
pp. S317-S318
Author(s):  
Brian W. Lee ◽  
Dona Rani C. Kathirithamby ◽  
Cesar Colasante ◽  
Kyle Menze ◽  
Kyle Silva ◽  
...  
Keyword(s):  
Case Report ◽  
3D Printed ◽  
Hypoplastic Thumb

3D printed titanium prosthesis reconstruction following subtotal maxillectomy for myoepithelial carcinoma – a case report

2020 ◽  
Vol 121 (2) ◽  
pp. 175-178 ◽  
Author(s):  
M.E. Roos ◽  
J. Claassen ◽  
G. Booysen ◽  
J. van den Heever ◽  
R.Y. Seedat
Keyword(s):  
Case Report ◽  
Myoepithelial Carcinoma ◽  
3D Printed
Sign in / Sign up

Export Citation Format

Share Document