Heat transfer process in direct contact evaporator. 2nd report Boiling regime and heat transfer characteristics.

1986 ◽  
Vol 52 (475) ◽  
pp. 1379-1386
Author(s):  
Yasunobu FUJITA ◽  
Kunio HIRAHAYA ◽  
Shinji MATSUO ◽  
Kaneyasu NISHIKAWA
2021 ◽  
Vol 2039 (1) ◽  
pp. 012011
Author(s):  
N N Kozhukhov ◽  
E A Kozhukhova ◽  
D A Konovalov ◽  
D A Prutskikh ◽  
V I Perunova

Abstract The paper presents the results of modeling the heat transfer process in a channel filled with a porous medium. Moreover, the porosity changes according to the specified law along one of the coordinates. It is shown that an element with anisotropic porosity has better heat transfer characteristics in comparison with an element with a homogeneous porous structure.


Author(s):  
Mengwei Zhang ◽  
Bin Zhang ◽  
Jianqiang Shan

Nuclear reactor severe accidents can lead to the release of a large amount of radioactive material and cause immense disaster to the environment. Since the Fukushima nuclear accident in Japan, the severe accident research has drawn worldwide attention. Based on the one-dimensional heat conduction model, a DEBRIS-HT program for analyzing the heat transfer characteristics of a debris bed after a severe accident of a sodium-cooled fast reactor was developed. The basic idea of the DEBRIS-HT program is to simplify the complex energy transfer process in the debris bed to a simple one-dimensional heat transfer problem by solving the equivalent thermal conductivity in different situations. In this paper, the DEBRIS-HT program code is prepared by using the existing model and compared with the experimental results. The results show that the DEBRIS-HT program can correctly predict the heat transfer process in the fragment bed. In addition, the heat transfer characteristics analysis program is also used to model the core catcher of the China fast reactor. Firstly, the dryout heat flux when all of molten core dropped on the core catcher was calculated, which was compared with the result of Lipinski’s zero dimensional model, and the error between two values is only 11.2%. Then, the temperature distribution was calculated with the heat power of 15MW.


Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-18
Author(s):  
Fa Wan ◽  
Zhong-Ming Jiang

The contradiction between supply and demand of energy leads to more and more attention on the large-scale energy storage technology; Compressed Air Energy Storage (CAES) technology is a new energy storage technology that is widely concerned in the world. The research of coupled heat transfer and seepage in fractured surrounding rocks is the necessary basis to evaluate the operation safety and effectiveness of CAES. Current studies point to the possibility of cracking in concrete liner seals, but the thermodynamic processes and leakage characteristics of compressed air in the presence of cracking and the heat transfer characteristics of seepage have not been addressed and reported. In order to investigate the leakage, the gas seepage and heat transfer law in fractured rock when the hard rock CAES gas reservoir seal cracks, the COMSOL fracture Darcy module, and the non-Darcy Forchheimer model are used as the constitutive seepage. The global ODE is used to calculate the thermodynamic process of compressed air in gas storage with coupled seepage and heat transfer process. The pressure and temperature of compressed air are obtained as the unsteady boundary of the seepage heat transfer model. A program for calculating the seepage and heat transfer characteristics of fractured surrounding rock in the CAES gas reservoir is established. On this basis, with the proposed Suichang CAES cavern as the background, the seepage and heat transfer characteristics of the fractured surrounding rock of the gas storage are studied. The results showed that when there are fewer cracks in the lining and surrounding rock of the air reservoir, the air pressure decreases due to a small amount of air leakage after 30 operation cycles, and the leakage rate of each cycle is 0.7% of the gas storage capacity, but it still meets the engineering requirements. If the plant is operating under these conditions, the charging rate will need to be increased by 1.2 kg/s per cycle charging stage. In the discharging and power generation phase, the high-pressure air that previously percolated into the rock mass cracks could flow back into the air storage through the lining cracks. Therefore, it is incorrect and unreliable to consider the gas which flows out from the inner surface of the lining as unusable. When the lining crack width is less than 0.3 mm, the seepage flow is Darcy flow and the non-Darcy effect can be ignored; when the lining crack width is greater than 0.5 mm, the non-Darcy effect of seepage cannot be ignored. The gas velocity in the surrounding rock fracture medium is on the order of 0.01 m/s with an influence range of over 100 m, and the gas velocity in the pore medium is on the order of 10-6 m/s with an influence range of 50 m. The findings of this study contribute to a better understanding of the interaction between the thermodynamic properties of compressed air and the seepage heat transfer process in compressed air storage underground reservoirs, as well as the gas leakage process in the event of liner seal cracking.


Author(s):  
Qingtai Xiao ◽  
Wen Luo ◽  
Junwei Huang ◽  
Jianxin Xu ◽  
Hua Wang

By bringing two immiscible fluids at different temperatures into a direct contact heat exchanger (DCHE), bubble swarms are produced in the dual-loop ORC direct contact boiling heat transfer process. The aim of this paper is to make effort to explore the interplay between mixing state quality and heat transfer performance of fluids in the DCHE. Through flow visualization of this mixing process, a simple image analysis technique is introduced to represent the formation and evolution of vapor around the injected coolant droplets. Description of the boiling heat transfer process is here achieved by average volumetric heat transfer coefficient (VHTC). Experimental results attest that the proposed mixing index is powerful and sufficient compared with the Betti numbers method for the mixing quality quantification of bubbles inside DCHE. The synergistic association between the fluids mixing process and the heat transfer process is investigated by statistical regression model of new mixing index and VHTC. The contributions, including the data from monitoring practice in ORC heat transfer system and the proposed way, are presented to delve into the transient behaviors comparison of various fluids mixing and heat transfer processes conveniently.


Sign in / Sign up

Export Citation Format

Share Document