How to Use Drill String Vibration Data to Reveal Geology Phenomena in Geosteering Jobs: An Application Sensor at the Bit

2017 ◽  
Author(s):  
Eri Sarmantua Sitinjak ◽  
Baladika Kurniawan ◽  
Yusuf Besol
Keyword(s):  
Drill String ◽  
Vibration Data ◽  
String Vibration

ROP Modeling using Neural Network and Drill String Vibration Data

2012 ◽  
Author(s):  
Abdolali Esmaeili ◽  
Behzad Elahifar ◽  
Rudolf Konrad Fruhwirth ◽  
Gerhard Thonhauser
Keyword(s):  
Neural Network ◽  
Drill String ◽  
Vibration Data ◽  
String Vibration

Diffractive index determination by Tikhonov regularization on forced string vibration data

2009 ◽  
Author(s):  
Irina Asekritova ◽  
Börje Nilsson ◽  
Sara Rydström ◽  
Börje Nilsson ◽  
Louis Fishman ◽  
...  
Keyword(s):  
Tikhonov Regularization ◽  
Vibration Data ◽  
String Vibration

Experimental Evaluation of Real-Time Mechanical Formation Classification using Drill String Vibration Measurements

2012 ◽  
Author(s):  
Abdolali Esmaeili ◽  
Behzad Elahifar ◽  
Rudolf Konrad Fruhwirth ◽  
Gerhard Thonhauser
Keyword(s):  
Real Time ◽  
Experimental Evaluation ◽  
Drill String ◽  
Vibration Measurements ◽  
String Vibration

Longitudinal and Angular Drill-String Vibrations With Damping

1968 ◽  
Vol 90 (4) ◽  
pp. 671-679 ◽  
Author(s):  
D. W. Dareing ◽  
B. J. Livesay
Keyword(s):  
Viscous Friction ◽  
Field Measurements ◽  
Computer Programs ◽  
Drill String ◽  
Recording Instrument ◽  
String Vibration ◽  
String Vibrations ◽  
Different Types ◽  
Drilling Operations ◽  
Computer Calculations

This paper discusses longitudinal and angular drill-string vibrations and supporting field measurements taken with a special downhole recording instrument. Computer programs based on the theory are used to calculate longitudinal and angular vibrations (caused by periodic bit motions) along the drill string; field measurements made during actual drilling operations are used to check computer calculations. The main difference between this and other theory on the same problem is the inclusion of friction, which acts along the length of a drill string and impedes longitudinal and angular vibrations. For the sake of simplicity, the effect of different types of friction, such as fluid, rubbing, and material, which act along the string, is approximated by the effect produced by viscous friction. This approximation is generally accepted and appears to give adequate results for the drill-string vibration problem.

Formation Prediction Model based on Drill String Vibration Measurements Using Laboratory Scale Rig

2013 ◽  
Author(s):  
Abdolali Esmaeili ◽  
Behzad Elahifar ◽  
Rudolf Konrad Fruhwirth ◽  
Gerhard Thonhauser
Keyword(s):  
Prediction Model ◽  
Drill String ◽  
Laboratory Scale ◽  
Vibration Measurements ◽  
String Vibration ◽  
Model Based

A Periodic Noise Separation Method Research of well Field Three-Dimensional Drill String Vibration Signal

2013 ◽  
Vol 318 ◽  
pp. 27-32
Author(s):  
Hao Cheng Wu ◽  
Yong Shou Dai ◽  
Wei Feng Sun ◽  
Li Gang Li ◽  
Ya Nan Zhang
Keyword(s):  
Independent Component Analysis ◽  
Vibration Signal ◽  
Component Analysis ◽  
Drill String ◽  
Independent Component ◽  
Analysis Algorithm ◽  
String Vibration ◽  
Periodic Noise ◽  
Well Field ◽  
Independent Component Analysis Algorithm

Periodic noise is an important manifestation of the drill string vibration signal noise. In order to extract the characteristics of the signals which reflect the situation of the tools in drilling, the periodic components which influence the original drill string vibration signal in the well field were researched and the independent component analysis algorithm which is on the basis of negative entropy for periodic vibration noise separation was adopted. At the same time, the effect of algorithm demixing was improved where periodic noise components which existed in three directions of drill string vibration signals were used, combining with the improved particle swarm optimization algorithm to seek the optimal mixed matrix by which the multi-channel mixed-signal of independent component analysis algorithm could be structured. This method in operation was fast. And after separation each signal was of high similarity. Through the experimental simulation, the method was proven effective in the drill string vibration periodic noise signal separation.

Research on Cepstrum Analysis of Drill String Vibration and Extraction of Bit Source Signals

2010 ◽  
Vol 53 (4) ◽  
pp. 684-692
Author(s):  
He-Zhen WU ◽  
Hong-Kui GE ◽  
Ding-Hui YANG ◽  
Bin LU ◽  
Lai-Ju HAN ◽  
...  
Keyword(s):  
Drill String ◽  
String Vibration ◽  
Cepstrum Analysis ◽  
Source Signals

A Modified Model for Friction Reduction by Vibrating Drill-String Longitudinally

2014 ◽  
Vol 535 ◽  
pp. 597-601 ◽  
Author(s):  
Peng Wang ◽  
Hong Jian Ni ◽  
Zhi Na Li ◽  
Rui He Wang
Keyword(s):  
Drill String ◽  
Friction Reduction ◽  
Contact Theory ◽  
Rock Surface ◽  
Modified Model ◽  
String Vibration ◽  
Tangential Stiffness ◽  
Proposed Model ◽  
Drilling Method ◽  
Coulomb Model

Drill-string vibration excitation longitudinally is a potential drilling method for reducing friction between drill-string and borehole rock. This article assumes that borehole rock surface is composed of elliptical asperities, based on elastic-plastic contact theory, a modified model for friction reduction by vibrating drill-string longitudinally is developed. The results show that the tangential stiffness of borehole rock surface decreased with increasing ovality of asperity. Further, at the same ovality, thin and tall asperity has bigger tangential stiffness than short and fat asperity. Only when the tangential stiffness of borehole rock is greater than a certain threshold, the friction force calculated by proposed model in this paper can appear reverse phenomenon. When the tangential stiffness tends to infinity, the result tends to Coulomb model. The conclusions provide basis for research and application of drill-string vibration longitudinally friction reduction technology.

Sign in / Sign up

Export Citation Format

Share Document