Kinetics and selectivity of methane oxidation on an IrO2(110) film

Undercoordinated, bridging O-atoms (Obr) are highly active as H-acceptors in alkane dehydrogenation on IrO2(110) surfaces but transform to HObr groups that are inactive toward hydrocarbons. The low C-H activity and high stability of the HObr groups cause the kinetics and product selectivity during CH4 oxidation on IrO2(110) to depend sensitively on the availability of Obr atoms prior to the onset of product desorption. From temperature programmed reaction spectroscopy (TPRS) and kinetic simulations, we identified two Obr-coverage regimes that distinguish the kinetics and product formation during CH4 oxidation on IrO2(110). Under excess Obr conditions, when the initial Obr coverage is greater than that needed to oxidize all the CH4 to CO2 and HObr groups, complete CH4 oxidation is dominant and produces CO2 in a single TPRS peak between 450 and 500 K. However, under Obr-limited conditions, nearly all the initial Obr atoms are deactivated by conversion to HObr or abstracted after only a fraction of the initially adsorbed CH4 oxidizes to CO2 and CO below 500 K. Thereafter, some of the excess CHx groups abstract H and desorb as CH4 above ~500 K while the remainder oxidize to CO2 and CO at a rate that is controlled by the rate at which Obr atoms are regenerated from HObr during the formation of CH4 and H2O products. We also show that chemisorbed O-atoms (“on-top O”) on IrO2(110) enhance CO2 production below 500 K by efficiently abstracting H from Obr atoms and thereby increasing the coverage of Obr atoms available to completely oxidize CHx groups at low temperature. Our results provide new insights for understanding factors which govern the kinetics and selectivity during CH4 oxidation on IrO2(110) surfaces.

Reactivity of Iridium Complexes of a Triphosphorus-Pincer Ligand Based on a Secondary Phosphine. Catalytic Alkane Dehydrogenation and the Origin of Extremely High Activity

The selective functionalization of alkanes and alkyl groups is a major goal of chemical catalysis. Toward this end, a bulky triphosphine with a central secondary phosphino group, bis(2 di-t-butyl-phosphinophenyl)phosphine (tBuPHPP), has been synthesized. When complexed to iridium it adopts a meridional (“pincer”) configuration. The secondary phosphino H atom can undergo migration to iridium to give an anionic phosphido-based-pincer (tBuPPP) complex. We describe novel metal-ligand cooperativity of the iridium-phosphido unit. Stoichiometric reactions of the (tBuPPP)Ir complexes reflect a distribution of steric bulk around the iridium center in which the coordination site trans to the phosphido group is quite crowded, one coordination site cis to the phosphido is even more crowded, while the remaining site is particularly open. The (tBuPPP)Ir precursors are the most active catalysts reported to date for dehydrogenation of n-alkanes, by about two orders of magnitude. The electronic properties of the iridium center are very similar to that of well-known analogous (RPCP)Ir catalysts. Accordingly, DFT calculations predict that (tBuPPP)Ir and (tBuPCP)Ir are, intrinsically, comparably active for alkane dehydrogenation. While dehydrogenation by (RPCP)Ir proceeds through an intermediate trans-(PCP)IrH2(alkene), (tBuPPP)Ir follows a pathway proceeding via cis-(PPP)IrH2(alkene), thereby circumventing unfavorable placement of the alkene at the bulky site trans to phosphorus. (tBuPPP)Ir and (tBuPCP)Ir, however, have analogous resting states: square planar (pincer)Ir(alkene). Alkene coordination at the crowded trans site is therefore unavoidable in the resting states. Thus the resting state of the (tBuPPP)Ir catalyst is destabilized by the unusual architecture of the ligand, and this is largely responsible for its unusually high catalytic activity.