Kinetic Measurements of Texture and Microstructural Evolution using Orientation Distribution Function and Residual Stress Relaxation

2008 ◽  
pp. 717-723
Author(s):  
S. Saimoto ◽  
J. Cooley ◽  
C. Gabryel
Keyword(s):  
Residual Stress ◽  
Distribution Function ◽  
Stress Relaxation ◽  
Microstructural Evolution ◽  
Orientation Distribution Function ◽  
Orientation Distribution ◽  
Kinetic Measurements ◽  
Residual Stress Relaxation

Comparative study of the effective parameters on residual stress relaxation in welded aluminum plates under cyclic loading

2020 ◽  
Vol 21 (5) ◽  
pp. 505
Author(s):  
Yousef Ghaderi Dehkordi ◽  
Ali Pourkamali Anaraki ◽  
Amir Reza Shahani
Keyword(s):  
Residual Stress ◽  
Cyclic Loading ◽  
Stress Relaxation ◽  
Stress Amplitude ◽  
Cyclic Plasticity ◽  
Mean Stress ◽  
Effective Parameters ◽  
Perfect Plasticity ◽  
Residual Stress Relaxation ◽  
Aluminum Plates

The prediction of residual stress relaxation is essential to assess the safety of welded components. This paper aims to study the influence of various effective parameters on residual stress relaxation under cyclic loading. In this regard, a 3D finite element modeling is performed to determine the residual stress in welded aluminum plates. The accuracy of this analysis is verified through experiment. To study the plasticity effect on stress relaxation, two plasticity models are implemented: perfect plasticity and combined isotropic-kinematic hardening. Hence, cyclic plasticity characterization of the material is specified by low cycle fatigue tests. It is found that the perfect plasticity leads to greater stress relaxation. In order to propose an accurate model to compute the residual stress relaxation, the Taguchi L18 array with four 3-level factors and one 6-level is employed. Using statistical analysis, the order of factors based on their effect on stress relaxation is determined as mean stress, stress amplitude, initial residual stress, and number of cycles. In addition, the stress relaxation increases with an increase in mean stress and stress amplitude.

Influence of extinction phenomenon on determination of the orientation distribution function

2006 ◽  
Vol 2006 (suppl_23_2006) ◽  
pp. 175-180
Author(s):  
G. Gómez-Gasga ◽  
T. Kryshtab ◽  
J. Palacios-Gómez ◽  
A. de Ita de la Torre
Keyword(s):  
Distribution Function ◽  
Orientation Distribution Function ◽  
Orientation Distribution

scholarly journals Prediction of Residual Stress Relaxation of Shot Peened 2024-T351 Aluminum Alloy: Part 1

2011 ◽  
Vol 462-463 ◽  
pp. 1355-1360
Author(s):  
Omar Suliman Zaroog ◽  
Aidy Ali ◽  
Sahari B. Barkawi
Keyword(s):  
Residual Stress ◽  
Stress Relaxation ◽  
Shot Peening ◽  
Applied Load ◽  
Cold Work ◽  
Cyclic Tests ◽  
Initial State ◽  
Loading Cycle ◽  
Residual Stress Relaxation ◽  
Alloy Part

It is important to account for residual stress relaxation phenomenon in the design of the component. Specimens of 2024-T351 aluminium alloy were used in this study. The specimens were shot peened under three different shot peening intensities. Cyclic tests for two load magnitudes were performed for 1, 2, 10, 1000 and 10000 cycles. Residual stresses, microhardness and the cold work percentage were measured at initial state and after each loading cycle for the three shot peening intensities and for the two loads. The study revealed that most of the drop in the residual stress, microhardness and cold work happened in the first cycle are dependent on the applied load.

A software for diffraction stress factor calculations for textured materials

2012 ◽  
Vol 27 (2) ◽  
pp. 114-116 ◽  
Author(s):  
Thomas Gnäupel-Herold
Keyword(s):  
Distribution Function ◽  
Pole Figure ◽  
Elastic Constants ◽  
Orientation Distribution Function ◽  
Lattice Strain ◽  
Orientation Distribution ◽  
Crystallite Orientation ◽  
Interaction Models ◽  
Grain Interaction ◽  
Textured Materials

A software for the calculation of diffraction elastic constants (DEC) for materials both with and without preferred orientation was developed. All grain-interaction models that can use the crystallite orientation distribution function (ODF) are incorporated, including Kröner, Hill, inverse Kröner, and Reuss. The functions of the software include: reading the ODF in common textual formats, pole figure calculation, calculation of DEC for different (hkl,φ,ψ), calculation of anisotropic bulk constants from the ODF, calculation of macro-stress from lattice strain and vice versa, as well as mixture ratios of (hkl) of overlapped reflections in textured materials.

Sign in / Sign up

Export Citation Format

Share Document