Influence of Sintering and Thermomechanical Treatment on Microstructure and Properties of W-Ni-Fe Alloys

1989 ◽  
pp. 243-254 ◽  
Author(s):  
M. Mitkov ◽  
W. A. Kaysser
Keyword(s):  
Thermomechanical Treatment ◽  
Microstructure And Properties ◽  
Fe Alloys

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

2017 ◽  
pp. 251-262
Author(s):  
Guo-huan Bao ◽  
Yi Chen ◽  
Ji-en Ma ◽  
You-tong Fang ◽  
Liang Meng ◽  
...  
Keyword(s):  
Cold Drawing ◽  
Microstructure And Properties ◽  
Fe Alloys

Regulation Mechanism of Novel Thermomechanical Treatment for Microstructure and Properties of 2E12 Aluminum Alloy

2015 ◽  
Vol 44 (10) ◽  
pp. 2341-2346
Author(s):  
Chen Zhiguo ◽  
Ren Jieke ◽  
Zhang Jishuai ◽  
Chen Jiqiang ◽  
Huang Yujin ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Thermomechanical Treatment ◽  
Regulation Mechanism ◽  
Microstructure And Properties

Regulation Mechanism of Novel Thermomechanical Treatment on Microstructure and Properties in Al-Zn-Mg-Cu Alloy

2015 ◽  
Vol 25 (2) ◽  
pp. 359-364 ◽  
Author(s):  
Zhiguo Chen ◽  
Jieke Ren ◽  
Jishuai Zhang ◽  
Jiqiang Chen ◽  
Liang Fang
Keyword(s):  
Thermomechanical Treatment ◽  
Regulation Mechanism ◽  
Microstructure And Properties ◽  
Cu Alloy

Effects of Thermomechanical Treatment Process on the Microstructure and Properties of 7A04 Aluminum Alloy

2011 ◽  
Vol 335-336 ◽  
pp. 805-808 ◽  
Author(s):  
Shi Xing Zhang ◽  
Hai Hong Wu ◽  
Gang Yi Cai
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Thermomechanical Treatment ◽  
Ageing Time ◽  
Solution Treatment ◽  
Second Phase ◽  
Microstructure And Properties ◽  
Treatment Processes ◽  
Phase Precipitate ◽  
Peak Value

The mechanical properties of a 7A04 aluminum alloy were improved by deformation strengthening and phase transformations strengthening adopting thermomechanical treatment, whose process include solution treatment, deformation treatment and ageing treatment in turn. The paper focuses on the influences of deforming degree and ageing process on microstructure and properties of 7A04 aluminum alloy. The experimental results show that hardness increased with increasing deformation ratio, and the value are greatly higher than that of samples after solution treatment. The results of ageing after deformation show that the hardness enhanced with prolonging the ageing time, which reach the peak value at 16 hours. In addition, the microstructure became more homogeneous and the grain was refined obviously by metallography microscope observation. The second phase precipitate dispersedly to strengthen the alloy. Above all, in order to obtain the better mechanical properties, the optimal thermomechanical treatment processes are solution treatment at 470°C for 2h, deformation with ratio of 40% as well as ageing at 120°C for 16h.

Effects of Thermomechanical Treatment Process on the Microstructure and Properties of Al-Zn-Mg Alloy

2011 ◽  
Vol 239-242 ◽  
pp. 847-850
Author(s):  
Gang Yi Cai ◽  
Yu Yong Yang ◽  
Xiao Hua Li
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Thermomechanical Treatment ◽  
Ageing Time ◽  
Solution Treatment ◽  
Second Phase ◽  
Microstructure And Properties ◽  
Treatment Processes ◽  
Phase Precipitate ◽  
Peak Value

The mechanical properties of Al-Zn-Mg aluminum alloy were improved by deformation strengthening and transformations strengthening adopting thermomechanical treatment, whose process are solution treatment, preageing treatment, deformation treatment and ageing treatment in turn. The paper focuses on the influences of deforming degree and ageing process on microstructure and properties of Al-Zn-Mg aluminum alloy. The experimental results show that hardness increased with increasing deformation ratio, and the value are greatly higher than that of samples after solution treatment. The results of ageing after deformation show that the hardness enhanced with prolonging the ageing time, which reach the peak value at 16 hours. In addition, the microstructure became more homogeneous and the grain was refined obviously by metallography microscope observation. The second phase precipitate dispersedly to strengthen the alloy. Above all, in order to obtain the better mechanical properties, the optimal thermomechanical treatment processes are solution treatment at 470°C for 2h, preageing treatment at 140°C for 24h, deformation with ratio of 40% as well as ageing at 120°C for 16h.

Evolution of the microstructure and properties of a Cu–Cr-(Mg) Alloy upon thermomechanical treatment

2020 ◽  
pp. 157582
Author(s):  
Hao Zeng ◽  
Han Sui ◽  
Shanjiang Wu ◽  
Jinping Liu ◽  
Hang Wang ◽  
...  
Keyword(s):  
Thermomechanical Treatment ◽  
Mg Alloy ◽  
Microstructure And Properties

scholarly journals Microstructure and properties of cold drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe alloys

2015 ◽  
Vol 16 (8) ◽  
pp. 622-629 ◽  
Author(s):  
Guo-huan Bao ◽  
Yi Chen ◽  
Ji-en Ma ◽  
You-tong Fang ◽  
Liang Meng ◽  
...  
Keyword(s):  
Cold Drawing ◽  
Microstructure And Properties ◽  
Fe Alloys

Effect of thermomechanical treatment on microstructure and properties of Cu-Cr-Zr-Ag alloy

Rare Metals ◽  
2011 ◽  
Vol 30 (6) ◽  
pp. 650-656 ◽  
Author(s):  
Haofeng Xie ◽  
Xujun Mi ◽  
Guojie Huang ◽  
Baodong Gao ◽  
Xiangqian Yin ◽  
...  
Keyword(s):  
Thermomechanical Treatment ◽  
Microstructure And Properties
Sign in / Sign up

Export Citation Format

Share Document