Distribution of disperse-phase vapors in a high-temperature gas flow

1985 ◽  
Vol 48 (2) ◽  
pp. 131-133
Author(s):  
D. I. Lamden ◽  
O. G. Stonik
Keyword(s):  
High Temperature ◽  
Disperse Phase ◽  
Gas Flow ◽  
High Temperature Gas

DISPERSED PHASE VELOCITY IN A HIGH-TEMPERATURE GAS FLOW

2019 ◽  
Vol 23 (4) ◽  
pp. 319-328
Author(s):  
Dmitry V. Nesterovich ◽  
Oleg G. Penyazkov ◽  
Yu. A. Stankevich ◽  
M. S. Tretyak ◽  
Vladimir V. Chuprasov ◽  
...  
Keyword(s):  
High Temperature ◽  
Phase Velocity ◽  
Gas Flow ◽  
Dispersed Phase ◽  
High Temperature Gas

Comparative Study of GaN Growth Process by MOVPE

1999 ◽  
Vol 572 ◽  
Author(s):  
Jingxi Sun ◽  
J. M. Redwing ◽  
T. F. Kuech
Keyword(s):  
High Temperature ◽  
Comparative Study ◽  
Gas Phase ◽  
Residence Time ◽  
Gas Flow ◽  
Flow Sheet ◽  
Flow Zone ◽  
High Quality ◽  
Phase Temperature ◽  
High Temperature Gas

ABSTRACTA comparative study of two different MOVPE reactors used for GaN growth is presented. Computational fluid dynamics (CFD) was used to determine common gas phase and fluid flow behaviors within these reactors. This paper focuses on the common thermal fluid features of these two MOVPE reactors with different geometries and operating pressures that can grow device-quality GaN-based materials. Our study clearly shows that several growth conditions must be achieved in order to grow high quality GaN materials. The high-temperature gas flow zone must be limited to a very thin flow sheet above the susceptor, while the bulk gas phase temperature must be very low to prevent extensive pre-deposition reactions. These conditions lead to higher growth rates and improved material quality. A certain range of gas flow velocity inside the high-temperature gas flow zone is also required in order to minimize the residence time and improve the growth uniformity. These conditions can be achieved by the use of either a novel reactor structure such as a two-flow approach or by specific flow conditions. The quantitative ranges of flow velocities, gas phase temperature, and residence time required in these reactors to achieve high quality material and uniform growth are given.

scholarly journals New high temperature gas flow cell developed at ISIS

2010 ◽  
Vol 251 ◽  
pp. 012090 ◽  
Author(s):  
R Haynes ◽  
S T Norberg ◽  
S G Eriksson ◽  
M A H Chowdhury ◽  
C M Goodway ◽  
...  
Keyword(s):  
High Temperature ◽  
Gas Flow ◽  
Flow Cell ◽  
High Temperature Gas

Study on Drying Behavior of Coal in High Temperature Gas Flow

2002 ◽  
Vol 2002 (0) ◽  
pp. 93-94
Author(s):  
Yutaka TAKENO ◽  
Yoshinori OTANI ◽  
Hiroaki KANEMOTO
Keyword(s):  
High Temperature ◽  
Gas Flow ◽  
Drying Behavior ◽  
High Temperature Gas

Numerical Investigation of Combustible Channel Walls Ignited by Gas Flow

2014 ◽  
Vol 1013 ◽  
pp. 295-299
Author(s):  
Oleg V. Matvienko ◽  
Aleksei Bubenchikov
Keyword(s):  
Surface Layer ◽  
High Temperature ◽  
Heat Exchange ◽  
Chemical Reaction ◽  
Gas Flow ◽  
External Boundary ◽  
Self Heating ◽  
Conjugate Formulation ◽  
Ignition Characteristics ◽  
High Temperature Gas

A study is made of the process of ignition of reactive channel walls by a laminar flow of hot gases, including the stages of heating of a substance and of reacting in the surface layer with self-acceleration of the chemical reaction. The process is determined by the heat exchange between the gas and the wall, the strength of the heat source in the chemical-reaction zone, and the sink of heat due to conduction in the radial and axial directions. In the stage of self-heating, we can have heat sink not only deep into the wall and/or through its external boundary but into the gas flow as well. The problem has been solved in a conjugate formulation. The influence of the temperature, the velocity of the gas at the entrance to the channel, and the wall thickness on ignition characteristics has been studied.In spreading a high temperature gas flow in a channel which walls are made of reactable material there appears a problem dealing with the possibility of their ignition by the flow.

Fibrous nanocorundum products for use in a high-temperature gas flow

2013 ◽  
Vol 53 (6) ◽  
pp. 379-383 ◽  
Author(s):  
V. N. Sokov ◽  
V. V. Sokov
Keyword(s):  
High Temperature ◽  
Gas Flow ◽  
High Temperature Gas
Sign in / Sign up

Export Citation Format

Share Document