Acoustic damping performance of coupled Helmholtz resonators with a sharable perforated sidewall in the presence of grazing flow

In this work, modified designs of Helmholtz resonators with extended deflected neck are proposed, numerically evaluated and optimized aiming to achieve a better transmission loss performance over a broader frequency range. For this, 10 Helmholtz resonators with different extended neck configurations (e.g. the angle between extended neck and the y-axis) in the presence of a grazing flow are assessed. Comparison is then made between the proposed resonators and the conventional one, i.e. in the absence of an extended neck (i.e. Design A). For this, a two-dimensional linearized Navier Stokes equations-based model of a duct with the modified Helmholtz resonator implemented was developed in frequency domain. The model was first validated by comparing its numerical predictions with the experimental results available in the literature and the theoretical results. The model was then applied to evaluate the noise damping performance of the Helmholtz resonator with (1) an extended neck on the upstream side (Design B); (2) on the downstream side (Design C), (3) both upstream and downstream sides (Design D), (4) the angle between the extended neck and the y-axis, i.e. (a) 0°, (b) 30°, and (c) 45°, (d) 48.321°. In addition, the effects of the grazing flow Mach number (Ma) were evaluated. It was found that the transmission loss peaks of the Helmholtz resonator with the extended neck was maximized at Ma = 0.03 than at the other Mach numbers. Conventional resonator, i.e. Design A was observed to be associated with a lower transmission loss performance at a lower resonant frequency than those as observed on Designs B–D. Moreover, the optimum design of the proposed resonators with the extended neck is shown to be able to shift the resonant frequency by approximately 90 Hz, and maximum transmission loss could be increased by 28–30 dB. In addition, the resonators with extended necks are found to be associated with two or three transmission loss peaks, indicating that these designs have a broader effective frequency range. Finally, the neck deflection angles of 30° and 45° are shown to be involved with better transmission loss peaks than that with a deflection angle of 0°. In summary, the present study sheds light on maximizing the resonator’s noise damping performances by applying and optimizing an extended neck.

Download Full-text

Experimental Study on Damping Acoustic Pressure Pulsations in Pipeline Systems Using Helmholtz Resonators

Journal of Pressure Vessel Technology ◽

10.1115/1.4045224 ◽

2019 ◽

Vol 142 (2) ◽

Cited By ~ 1

Author(s):

Karim Sachedina ◽

Atef Mohany ◽

Marwan Hassan

Keyword(s):

Acoustic Waves ◽

Acoustic Pressure ◽

Excitation Frequency ◽

Acoustic Resonance ◽

Pipeline System ◽

Pressure Pulsations ◽

Acoustic Damping ◽

Helmholtz Resonators ◽

Acoustic Standing Wave ◽

Pipeline Systems

Abstract Acoustic pressure pulsations can be problematic in industrial pipelines, especially when the excitation frequency matches an acoustic resonance frequency of the pipeline. The objective of this paper is to investigate the effectiveness of Helmholtz resonators (HRs) in multiple arrangements on the attenuation of acoustic pressure pulsations in piping systems. In a resonant pipeline (i.e., an acoustic standing wave scenario), maximal attenuation is achieved when the HR is inserted at the acoustic pressure antinode. The insertion loss (IL) in an off-resonant system is found to be relatively consistent, unless there is a coupling between the HR and the downstream end termination in which case there is a decrease in attenuation. Multiple, small-volume HRs in various configurations can achieve the same level of damping as that of a single HR with the same total volume. Moreover, it is shown that the use of multiple HRs placed at strategic spacing intervals along the length of a pipeline can yield significant acoustic damping, without the need for characterizing the acoustic waves in the pipeline system. An axial spacing of a quarter wavelength of the frequency of interest between multiple HRs is shown to increase the peak attenuation, which is indicative of a favorable coupling between HRs. The effect of flow velocity and its directionality with respect to the sound source is also investigated. The results presented in this paper provide practical techniques that can be used for the implementation of HR in pipeline systems.

Download Full-text