Analysis of plane wave propagation under the purview of three phase lag theory of thermoelasticity with non-local effect

2021 ◽  
Vol 88 ◽  
pp. 104235
Author(s):  
Rakhi Tiwari ◽  
Ravi Kumar
Keyword(s):  
Wave Propagation ◽  
Plane Wave ◽  
Local Effect ◽  
Phase Lag ◽  
Three Phase ◽  
Non Local ◽  
Plane Wave Propagation

scholarly journals Plane wave in non-local semiconducting rotating media with Hall effect and three-phase lag fractional order heat transfer

2021 ◽  
Vol 16 (1) ◽  
Author(s):  
Iqbal Kaur ◽  
Kulvinder Singh
Keyword(s):  
Plane Wave ◽  
Fractional Order ◽  
Density Wave ◽  
Transverse Displacement ◽  
Phase Lag ◽  
Wave Characteristics ◽  
Three Phase ◽  
Displacement Wave ◽  
Non Local ◽  
Two Temperatures

AbstractThis paper deals with the propagation of the plane wave in a nonlocal magneto-thermoelastic semiconductor solid with rotation. The fractional-order three-phase lag theory of thermoelasticity with two temperatures has been applied. When a longitudinal wave is incident on the surface z = 0, four types of reflected coupled longitudinal waves (the coupled longitudinal displacement wave, the coupled thermal wave, coupled carrier density wave, and coupled transverse displacement wave) are identified. The plane wave characteristics such as phase velocities, specific loss, attenuation coefficient, and penetration depth of various reflected waves are computed. The effects of two temperatures, non-local parameter, fractional order parameter, and Hall current on these wave characteristics are illustrated graphically with the use of MATLAB software.

scholarly journals Effects of Central Tube on Shape of Modal Duct of a Helicoid in a Simple Expansion Chamber

2018 ◽  
Vol 2018 ◽  
pp. 1-6
Author(s):  
Daniel Omondi Onyango ◽  
Robert Kinyua ◽  
Abel Nyakundi Mayaka
Keyword(s):  
Wave Propagation ◽  
Acoustic Wave ◽  
Plane Wave ◽  
Acoustic Pressure ◽  
Three Dimensional ◽  
The Other ◽  
Expansion Chamber ◽  
Central Tube ◽  
Simple Expansion ◽  
Plane Wave Propagation

The shape of the modal duct of an acoustic wave propagating in a muffling system varies with the internal geometry. This shape can be either as a result of plane wave propagation or three-dimensional wave propagation. These shapes depict the distribution of acoustic pressure that may be used in the design or modification of mufflers to create resonance at cut-off frequencies and hence achieve noise attenuation or special effects on the output of the noise. This research compares the shapes of acoustic duct modes of two sets of four pitch configurations of a helicoid in a simple expansion chamber with and without a central tube. Models are generated using Autodesk Inventor modeling software and imported into ANSYS 18.2, where a fluid volume from the complex computer-aided-design (CAD) geometry is extracted for three-dimensional (3D) analysis. Mesh is generated to capture the details of the fluid cavity for frequency range between 0 and 2000Hz. After defining acoustic properties, acoustic boundary conditions and loads were defined at inlet and outlet ports before computation. Postprocessed acoustic results of the modal shapes and transmission loss (TL) characteristics of the two configurations were obtained and compared for geometries of the same helical pitch. It was established that whereas plane wave propagation in a simple expansion chamber (SEC) resulted in a clearly defined acoustic pressure pattern across the propagation path, the distribution in the configurations with and without the central tube depicted three-dimensional acoustic wave propagation characteristics, with patterns scattering or consolidating to regions of either very low or very high acoustic pressure differentials. A difference of about 80 decibels between the highest and lowest acoustic pressure levels was observed for the modal duct of the geometry with four turns and with a central tube. On the other hand, the shape of the TL curve shifts from a sinusoidal-shaped profile with well-defined peaks and valleys in definite multiples of π for the simple expansion chamber, while that of the other two configurations depended on the variation in wavelength that affects the location of occurrence of cut-on or cut-off frequency. The geometry with four turns and a central tube had a maximum value of TL of about 90 decibels at approximately 1900Hz.

Plane wave propagation in microstretch thermoelastic medium with microtemperatures

2014 ◽  
Vol 21 (16) ◽  
pp. 3403-3416
Author(s):  
Rajneesh Kumar ◽  
Mandeep Kaur ◽  
SC Rajvanshi
Keyword(s):  
Wave Propagation ◽  
Plane Wave ◽  
Thermoelastic Medium ◽  
Plane Wave Propagation
Sign in / Sign up

Export Citation Format

Share Document