Flow boiling heat transfer in two-phase micro-channel heat sinks––II. Annular two-phase flow model

2003 ◽  
Vol 46 (15) ◽  
pp. 2773-2784 ◽  
Author(s):  
Weilin Qu ◽  
Issam Mudawar
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Flow Model ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Heat Sinks ◽  
Phase Flow ◽  
Micro Channel ◽  
Two Phase ◽  
Flow Boiling Heat Transfer

Flow Boiling Heat Transfer and Two-Phase Flow Instability of Nanofluids in a Minichannel

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Leyuan Yu ◽  
Aritra Sur ◽  
Dong Liu
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Two Phase Flow ◽  
Flow Instability ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Flow Instabilities ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Boiling Heat Transfer

Single-phase convective heat transfer of nanofluids has been studied extensively, and different degrees of enhancement were observed over the base fluids, whereas there is still debate on the improvement in overall thermal performance when both heat transfer and hydrodynamic characteristics are considered. Meanwhile, very few studies have been devoted to investigating two-phase heat transfer of nanofluids, and it remains inconclusive whether the same pessimistic outlook should be expected. In this work, an experimental study of forced convective flow boiling and two-phase flow was conducted for Al2O3–water nanofluids through a minichannel. General flow boiling heat transfer characteristics were measured, and the effects of nanofluids on the onset of nucleate boiling (ONB) were studied. Two-phase flow instabilities were also explored with an emphasis on the transition boundaries of onset of flow instabilities (OFI). It was found that the presence of nanoparticles delays ONB and suppresses OFI, and the extent is correlated to the nanoparticle volume concentration. These effects were attributed to the changes in available nucleation sites and surface wettability as well as thinning of thermal boundary layers in nanofluid flow. Additionally, it was observed that the pressure-drop type flow instability prevails in two-phase flow of nanofluids, but with reduced amplitude in pressure, temperature, and mass flux oscillations.

21821 Study on Flow Boiling Heat Transfer and Two-Phase Flow in Flat Mini-Channel

2007 ◽  
Vol 2007.13 (0) ◽  
pp. 97-98
Author(s):  
Yasuo Koizumi ◽  
Hiroyasu Ohtake ◽  
Tomonari Yamada ◽  
Naoki Uchida
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Boiling Heat Transfer

Two-Phase Flow and Heat Transfer in Rectangular Micro-Channels

2004 ◽  
Vol 126 (3) ◽  
pp. 288-300 ◽  
Author(s):  
Weilin Qu ◽  
Seok-Mann Yoon ◽  
Issam Mudawar
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Flow Patterns ◽  
Heat Sinks ◽  
Phase Flow ◽  
Micro Channel ◽  
Two Phase

Knowledge of flow pattern and flow pattern transitions is essential to the development of reliable predictive tools for pressure drop and heat transfer in two-phase micro-channel heat sinks. In the present study, experiments were conducted with adiabatic nitrogen-water two-phase flow in a rectangular micro-channel having a 0.406×2.032mm2 cross-section. Superficial velocities of nitrogen and water ranged from 0.08 to 81.92 m/s and 0.04 to 10.24 m/s, respectively. Flow patterns were first identified using high-speed video imaging, and still photos were then taken for representative patterns. Results reveal the dominant flow patterns are slug and annular, with bubbly flow occurring only occasionally; stratified and churn flow were never observed. A flow pattern map was constructed and compared with previous maps and predictions of flow pattern transition models. Features unique to two-phase micro-channel flow were identified and employed to validate key assumptions of an annular flow boiling model that was previously developed to predict pressure drop and heat transfer in two-phase micro-channel heat sinks. This earlier model was modified based on new findings from the adiabatic two-phase flow study. The modified model shows good agreement with experimental data for water-cooled heat sinks.

Proposed Correlation for Forced Convection Boiling Heat Transfer in Mini and Micro Channels With CO2 as a Fluid

2014 ◽  
Author(s):  
Mayank I. Vyas ◽  
Salim A. Channiwala ◽  
Mitesh N. Prajapati
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Working Fluid ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Boiling Heat Transfer ◽  
Micro Channels

After reviewing the available literature on flow boiling heat transfer in mini/micro tubes and channels, it is felt that there is need for predictive correlations which is applicable over wide range of parameters. In present work a new correlation for two-phase flow boiling heat transfer coefficient is developed, which has considered nucleate boiling and convective boiling heat transfer effect. To develop this correlation we have considered total 651 data points, which have been collected from the open available literature covering different operational conditions and different dimensions of channels. We have selected CO2 as a working fluid because it does not contain chlorine, hence an efficient and environmentally safe refrigerant and would be potential replacement for R-22. CO2 has unusual heat transfer and two-phase flow characteristics, and is very different from those of conventional refrigerant. Also a comparison of present correlation with the best published correlation for CO2 is done. The results of this comparison indicate that the new developed correlation is superior to published best correlation for CO2. Present correlation is also compared with best published correlation for all fluids and with the correlation developed by using CO2 data. The results of these both case, indicate that the present correlation is superior.

Sign in / Sign up

Export Citation Format

Share Document