In-vitro pulp chamber temperature rise during composite resin polymerization with various light-curing sources

1999 ◽  
Vol 15 (4) ◽  
pp. 275-281 ◽  
Author(s):  
M. Hannig ◽  
B. Bott
2008 ◽  
Vol 16 (5) ◽  
pp. 355-359 ◽  
Author(s):  
Thaise Graciele Carrasco ◽  
Laise Daniela Carrasco-Guerisoli ◽  
Izabel Cristina Fröner

Laser Physics ◽  
2021 ◽  
Vol 31 (5) ◽  
pp. 055601
Author(s):  
Sogol Saberi ◽  
Sima Shahabi ◽  
Saba Tohidkhah ◽  
Shiva Jafarnia ◽  
Parham Pedram

2010 ◽  
Vol 13 (3) ◽  
pp. 132 ◽  
Author(s):  
RajeshA.V Ebenezar ◽  
R Anilkumar ◽  
R Indira ◽  
S Ramachandran ◽  
MR Srinivasan

2010 ◽  
Vol 38 (2) ◽  
pp. 76-79 ◽  
Author(s):  
Bağdagül Helvacıoğlu Kivanç ◽  
Hacer Deniz Arisu ◽  
Özgür İlke Atasoy Ulusoy ◽  
Baran Can Sağlam ◽  
Güliz Görgül

2016 ◽  
Vol 7 (3) ◽  
pp. 184-191 ◽  
Author(s):  
Rajesh Harivadanbhai Mahant ◽  
Shraddha Chokshi ◽  
Rupal Vaidya ◽  
Pruthvi Patel ◽  
Asima Vora ◽  
...  

2007 ◽  
Vol 8 (4) ◽  
pp. 19-26 ◽  
Author(s):  
A. Rüya Yazici ◽  
Gerard Kugel ◽  
Azita Khanbodaghi

Abstract Aim Several new techniques and materials for in-office bleaching have been introduced recently. The aim of this in vitro study was to measure the temperature increase in the pulp chamber of extracted teeth produced by the Zoom!™ in-office bleaching system and to investigate the influence of this light in conjunction with the bleaching gel on pulp temperature rise. Methods and Materials Ten extracted, caries-free, unrestored human maxillary central incisor teeth were used for the study. The root of each tooth was cut approximately 2-3 mm apical to the cementoenamel junction (CEJ), and the apical orifice of the root canal was enlarged. The remaining pulp tissue was removed and the empty pulp chamber was filled with a heat sink compound. A thin K-type thermocouple was inserted into the pulp chamber through the cut root area. The root surfaces of the teeth were partially submerged in a water bath during the testing procedure at 37°C. A whitening gel containing 25% hydrogen peroxide was applied to the buccal surfaces of all ten teeth and exposed to a Zoom!™ activation light for twenty minutes for three times; this was designated as Group I. The same teeth were then exposed with the Zoom!™ light for the same time period without the application of the bleaching gel and designated as Group II. The intrapulpal temperature pre-treatment (baseline) and the temperature increase during treatment was measured for both treatment groups. Results There was a statistically significant difference between the two groups (p=0.003). Application of the Zoom!™ light in conjuction with the application of bleaching gel produced a greater temperature rise than did the light alone. The mean temperature rise for Group I (light and bleaching gel) was 1.11°C (0.18°C) and 1.01°C (0.12°C) for Group II (light alone) at the end of a five-minute exposure. Conclusion The Zoom!™ light either used with or without bleaching gel showed no significant increase in the intrapulpal temperature of teeth when used for the recommended exposure time. Citation Yazici AR, Khanbodaghi A, Kugel G. Effects of an In-office Bleaching System (ZOOM™) on Pulp Chamber Temperature In Vitro. J Contemp Dent Pract 2007 May;(8)4:019-026.


10.2341/05-26 ◽  
2006 ◽  
Vol 31 (2) ◽  
pp. 261-265 ◽  
Author(s):  
A. R. Yazici ◽  
A. Müftü ◽  
G. Kugel ◽  
R. D. Perry

Clinical Relevance The thickness of the residual dentin is a critical factor in the reducing thermal transfer to pulp, and this transfer varies with the curing unit used.


Sign in / Sign up

Export Citation Format

Share Document