A new dynamic hysteresis model for electrical steel sheet

2000 ◽  
Vol 275 (1-3) ◽  
pp. 197-201 ◽  
Author(s):  
T Chevalier ◽  
A Kedous-Lebouc ◽  
B Cornut ◽  
C Cester
Author(s):  
Brijesh Upadhaya ◽  
Floran Martin ◽  
Paavo Rasilo ◽  
Paul Handgruber ◽  
Anouar Belahcen ◽  
...  

Purpose Non-oriented electrical steel presents anisotropic behaviour. Modelling such anisotropic behaviour has become a necessity for accurate design of electrical machines. The main aim of this study is to model the magnetic anisotropy in the non-oriented electrical steel sheet of grade M400-50A using a phenomenological hysteresis model. Design/methodology/approach The well-known phenomenological vector Jiles–Atherton hysteresis model is modified to correctly model the typical anisotropic behaviour of the non-oriented electrical steel sheet, which is not described correctly by the original vector Jiles–Atherton model. The modification to the vector model is implemented through the anhysteretic magnetization. Instead of the commonly used classical Langevin function, the authors introduced 2D bi-cubic spline to represent the anhysteretic magnetization for modelling the magnetic anisotropy. Findings The proposed model is found to yield good agreement with the measurement data. Comparisons are done between the original vector model and the proposed model. Another comparison is also made between the results obtained considering two different modifications to the anhysteretic magnetization. Originality/value The paper presents an original method to model the anhysteretic magnetization based on projections of the anhysteretic magnetization in the principal axis, and apply such modification to the vector Jiles–Atherton model to account for the magnetic anisotropy. The replacement of the classical Langevin function with the spline resulted in better fitting. The proposed model could be used in the numerical analysis of magnetic field in an electrical application.


2012 ◽  
Vol 132 (11) ◽  
pp. 1033-1038
Author(s):  
Yuichiro Kai ◽  
Yuji Tsuchida ◽  
Takashi Todaka ◽  
Masato Enokizono

Author(s):  
Sampsa Vili Antero Laakso ◽  
Ugur Aydin ◽  
Peter Krajnik

AbstractOne of the most dominant manufacturing methods in the production of electromechanical devices from sheet metal is punching. In punching, the material undergoes plastic deformation and finally fracture. Punching of an electrical steel sheet causes plastic deformation on the edges of the part, which affects the magnetic properties of the material, i.e., increases iron losses in the material, which in turn has a negative effect on the performance of the electromagnetic devices in the final product. Therefore, punching-induced iron losses decrease the energy efficiency of the device. FEM simulations of punching have shown significantly increased plastic deformation on the workpiece edges with increasing tool wear. In order to identify the critical tool wear, after which the iron losses have increased beyond acceptable limits, the simulation results must be verified with experimental methods. The acceptable limits are pushed further in the standards by the International Electrotechnical Commission (IEC). The new standard (IEC TS 60034-30-2:2016) has much stricter limits regarding the energy efficiency of electromechanical machines, with an IE5 class efficiency that exceeds the previous IE4 class (IEC 60034-30-1:2014) requirements by 30%. The simulations are done using Scientific Forming Technologies Corporation Deform, a finite element software for material processing simulations. The electrical steel used is M400-50A, and the tool material is Vanadis 23, a powder-based high-speed steel. Vanadis 23 is a high alloyed powder metallurgical high-speed steel with a high abrasive wear resistance and a high compressive strength. It is suitable for cold work processing like punching. In the existing literature, FEM simulations and experimental methods have been incorporated for investigating the edge deformation properties of sheared surfaces, but there is a research gap in verifying the simulation results with the experimental methods. In this paper, FEM simulation of the punching process is verified using an electrical steel sheet from real production environment and measuring the deformation of the edges using microhardness measurements. The simulations show high plastic deformation 50 μm into the workpiece edge, a result that is shown to be in good agreement with the experimental results.


Sign in / Sign up

Export Citation Format

Share Document