An analysis of periodic discharge of powder from a cylindrical vessel

1992 ◽  
Vol 3 (2) ◽  
pp. 103-110 ◽  
Author(s):  
Akira Takami
2007 ◽  
Vol 43 (2) ◽  
pp. 161-172 ◽  
Author(s):  
M. Kirpo ◽  
A. Jakovičs ◽  
E. Baake ◽  
B. Nacke

2010 ◽  
Vol 488 (1-3) ◽  
pp. 1-6 ◽  
Author(s):  
Ken-ich Amano ◽  
Masahiro Kinoshita
Keyword(s):  

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
H. Al-Gahtani ◽  
A. Khathlan ◽  
M. Sunar ◽  
M. Naffa'a

The juncture of a small cylindrical nozzle to a large cylindrical vessel is very common in the pressure vessel industry. Upon fabrication, it is required that the whole structure is subjected to pressure testing. The test can be expensive as it necessitates pressurizing the whole structure typically having a large volume. Hence, it is proposed to make a “local test,” which is considerably simpler as it involves capping the small nozzle and testing only a relatively small portion of the structure. This paper investigates the accuracy and reliability of such an alternative test, using the finite-element method. Two different finite-element types are used in the study, specifically a shell-based element and a solid-based element. The verification of the finite-element results for two different cases shows that the models used in the study are valid. It also proves that the two element types yield very similar stress results. In addition, the study includes a numerical investigation of more than 40 different nozzle-to-vessel junctures with a wide range of parameters for the nozzle and vessel. The results indicate that the use of cylindrical caps that are slightly larger than the nozzle is not recommended as it produces stresses that are significantly different from those for the original required pressure test. As such, the study provides an estimate of the smallest size of the cap that may be used in the local test to generate stresses that agree with the full test. For most practical geometries, it is shown that the size of the cap needs to be at least 2–30 times larger than that of the nozzle, depending on the geometrical parameters of the juncture.


Author(s):  
Harold Jeffreys

When a vessel of liquid has been emptied and put aside, a thin film of liquid clings to the inside and gradually drains down to the bottom under the action of gravity. The layer being thin, the motion is very nearly laminar flow, and the curvature of the surface in a horizontal direction may be ignored. Thus the problem for a cylindrical vessel is reducible to that of a wet plate standing vertically.


The importance of the investigation here entered into,—inasmuch as it applies to most of the operations of nature as well as art,—appears so manifest, that we shall not recapitulate what the author advances on that subject. Before he proceeds to the detail of his experiments for the purpose of computing the emissions of heat from various bodies under a variety of circumstances, he finds it necessary to premise a minute description of the principal part of the apparatus he contrived for his purpose. This instrument consists of a hollow cylindrical vessel of brass, four inches long, and as many in diameter. It is closed at both ends; but has at one end a cylindrical neck about eight-tenths of an inch in diameter, by which it is occasionally filled with water of different temperatures, and through which also a thermometer, constructed for the purpose, is occasionally introduced, in order to ascertain the changes of temperature in the fluid. As it was in the first instance only meant to observe the quantity of heat that escapes through the sides of the vessel, two boxes were contrived, filled and covered with non-conducting substances, such as eiderdown, fur, &c., which were fitted to the two ends or flat surfaces of the cylinder. Six of these instruments, with proper stands, and auxiliary implements of obvious construction, were prepared for the sake of comparative experiments. A previous trial was made with two of the cylinders, the vertical polished sides of the one being naked, and those of the other covered with one thickness of fine white Irish linen, strained over the metallic surface. Here it was found, contrary to expectation, that in a certain space of time the covered cylinder had lost considerably more heat than the naked one.


1977 ◽  
Vol 20 (4) ◽  
pp. 548-551
Author(s):  
N. I. Nizhegorodov ◽  
A. Ya. Terletskii ◽  
V. F. Ignatov ◽  
V. V. Nikiforov

2001 ◽  
Vol 34 (7) ◽  
pp. 929-935 ◽  
Author(s):  
YOSHIYUKI KOMODA ◽  
YOSHIROU INOUE ◽  
YUSHI HIRATA

2001 ◽  
Vol 34 (7) ◽  
pp. 919-928 ◽  
Author(s):  
YOSHIYUKI KOMODA ◽  
YOSHIROU INOUE ◽  
YUSHI HIRATA

Sign in / Sign up

Export Citation Format

Share Document