Properties of Diagrams of Equilibrium Open Evaporation Accompanied by Instantaneous Chemical Reactions

Chemical reactions at a surface will in most cases show a measurable influence on the work function of the clean surface. This change of the work function δφ can be used to image the local distributions of the investigated reaction,.if one of the reacting partners is adsorbed at the surface in form of islands of sufficient size (Δ>0.2μm). These can than be visualized via a photoemission electron microscope (PEEM). Changes of φ as low as 2 meV give already a change in the total intensity of a PEEM picture. To achieve reasonable contrast for an image several 10 meV of δφ are needed. Dynamic processes as surface diffusion of CO or O on single crystal surfaces as well as reaction / diffusion fronts have been observed in real time and space.

Download Full-text

Microwaves: Application in Electron Microscopy

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100158248 ◽

1990 ◽

Vol 48 (3) ◽

pp. 140-141

Author(s):

Anthony S-Y Leong ◽

David W Gove

Keyword(s):

Electron Microscopy ◽

Light Microscopy ◽

Chemical Reactions ◽

Electromagnetic Waves ◽

Tissue Fixation ◽

Primary Method ◽

Dipolar Molecules ◽

Wide Range ◽

Time Required ◽

Cryostat Sections

Microwaves (MW) are electromagnetic waves which are commonly generated at a frequency of 2.45 GHz. When dipolar molecules such as water, the polar side chains of proteins and other molecules with an uneven distribution of electrical charge are exposed to such non-ionizing radiation, they oscillate through 180° at a rate of 2,450 million cycles/s. This rapid kinetic movement results in accelerated chemical reactions and produces instantaneous heat. MWs have recently been applied to a wide range of procedures for light microscopy. MWs generated by domestic ovens have been used as a primary method of tissue fixation, it has been applied to the various stages of tissue processing as well as to a wide variety of staining procedures. This use of MWs has not only resulted in drastic reductions in the time required for tissue fixation, processing and staining, but have also produced better cytologic images in cryostat sections, and more importantly, have resulted in better preservation of cellular antigens.

Download Full-text

Applications of SEM/EDXA in cement clinker investigation

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100177489 ◽

1990 ◽

Vol 48 (4) ◽

pp. 870-871

Author(s):

Arezki Tagnit-Hamou ◽

Shondeep L. Sarkar

Keyword(s):

Mineralogical Composition ◽

Physicochemical Characteristics ◽

Cement Clinker ◽

Accurate Information ◽

Phase Identification ◽

History Of ◽

Bulk Chemical ◽

Resolution Imaging ◽

Proven Method ◽

Instantaneous Chemical

All the desired properties of cement primarily depend on the physicochemical characteristics of clinker from which the cement is produced. The mineralogical composition of the clinker forms the most important parameter influencing these properties.Optical microscopy provides reasonably accurate information pertaining to the thermal history of the clinker, while XRDA still remains the proven method of phase identification, and bulk chemical composition of the clinker can be readily obtained from XRFA. Nevertheless, all these microanalytical techniques are somewhat limited in their applications, and SEM/EDXA combination fills this gap uniquely by virtue of its high resolution imaging capability and possibility of instantaneous chemical analysis of individual phases.Inhomogeneities and impurities in the raw meal, influence of kiln conditions such as sintering and cooling rate being directly related to the microstructure can be effectively determined by SEM/EDXA. In addition, several physical characteristics of cement, such as rhcology, grindability and hydraulicity also depend on the clinker microstructure.

Download Full-text