Prestressed Composite Steel Beam Design

1973 ◽  
Vol 99 (3) ◽  
pp. 301-319
Author(s):  
Subhash C. Anand ◽  
Ahmed Talesstchi
Keyword(s):  
Steel Beam ◽  
Beam Design ◽  
Composite Steel

Discussion of “Prestressed Composite Steel Beam Design”

1973 ◽  
Vol 99 (11) ◽  
pp. 2328-2329
Author(s):  
James W. Chai
Keyword(s):  
Steel Beam ◽  
Beam Design ◽  
Composite Steel

Closure to “Prestressed Composite Steel Beam Design”

1974 ◽  
Vol 100 (7) ◽  
pp. 1526-1526
Author(s):  
Subhash C. Anand ◽  
Ahmed Talesstchi
Keyword(s):  
Steel Beam ◽  
Beam Design ◽  
Composite Steel

scholarly journals A comparative study of beam design curves against lateral torsional buckling using AISC, EC and SP

2019 ◽  
Vol 15 (1) ◽  
pp. 25-32 ◽  
Author(s):  
Vera V Galishnikova ◽  
Tesfaldet H Gebre
Keyword(s):  
Steel Structures ◽  
Reduction Factor ◽  
Steel Beams ◽  
Steel Beam ◽  
Lateral Torsional Buckling ◽  
Torsional Buckling ◽  
Vertical Loading ◽  
Beam Design ◽  
Overall Stability

Introduction. Structural stability is an essential part of design process for steel structures and checking the overall stability is very important for the determination of the optimum steel beams section. Lateral torsional buckling (LTB) normally associated with beams subject to vertical loading, buckling out of the plane of the applied loads and it is a primary consideration in the design of steel structures, consequently it may reduce the load currying capacity. Methods. There are several national codes to verify the steel beam against LTB. All specifications have different approach for the treatment of LTB and this paper is concentrated on three different methods: America Institute of Steel Construction (AISC), Eurocode (EC) and Russian Code (SP). The attention is focused to the methods of developing LTB curves and their characteristics. Results. AISC specification identifies three regimes of buckling depending on the unbraced length of the member ( Lb ). However, EC and SP utilize a reduction factor (χ LT ) to treat lateral torsional buckling problem. In general, flexural capacities according to AISC are higher than those of EC and SP for non-compact sections.

Shrinkage tests of two full-scale composite trusses

1992 ◽  
Vol 19 (2) ◽  
pp. 296-309 ◽  
Author(s):  
D. J. Laurie Kennedy ◽  
Anita Brattland
Keyword(s):  
Concrete Beams ◽  
Concrete Slab ◽  
Shrinkage Strain ◽  
Steel Beam ◽  
Restrained Shrinkage ◽  
Test Results ◽  
Linear Strain ◽  
Shrinkage Behaviour ◽  
Composite Section ◽  
Composite Steel

The shrinkage behaviour of two composite trusses with a span of 11.5 m was studied. Shrinkage measurements to determine the effects of slab shrinkage on truss deflections and member strains were recorded over periods of 65 and 85 days. A method is developed to compute shrinkage deflections, based on equilibrium of the shrinkage-induced forces at midspan, which gives excellent agreement with the test results. This method assumes a linear strain distribution through the depth and is based on the free shrinkage strain of the concrete and the average stress–strain characteristics of the concrete in tension under restrained shrinkage conditions as it drys, creeps, and eventually may crack as it is gradually loaded from the green state. The method is extended to composite steel-beam concrete-slab members. It is equivalent to Branson's "composite section method" provided that the correct values for the shrinkage strain and the effective modulus of elasticity of the concrete in tension are used in the latter. Key words: behaviour, composite steel–concrete beams, trusses, shrinkage deflections.

The Overall Optimization of Djoué Composite Steel-Concrete Bridge in the Congo (Brazzaville) National Road One Phase- II Project

2012 ◽  
Vol 256-259 ◽  
pp. 1520-1527
Author(s):  
Rui Hui Jia ◽  
Yun Wei Chen ◽  
Yuan Qing Wang ◽  
Liang Zong ◽  
Jun Li ◽  
...  
Keyword(s):  
Phase Ii ◽  
Optimization Design ◽  
Steel Beam ◽  
Concrete Bridge ◽  
Follow Up Study ◽  
Bridge Type ◽  
Congo Brazzaville ◽  
National Road ◽  
Composite Steel

In order to learn more about the composite steel-concrete bridge which the Djoué bridge of Congo (Brazzaville) National Road One Phase- II Project has selected, promote the design technologies of bridges and better understand and improve the relevant standards, The overall optimization design analysis of Djoué Bridge aiming at saving steel and improving bearing capacity is necessary. The Doctor Bridge was used in optimization of bridge type, concrete thickness and height of steel beam and they have been selected. It can provide technical references for the construction of the Djoué Bridge, the follow-up study of the composite steel-concrete bridge and the specification improvement.

scholarly journals DEFORMATION PERFORMANCE OF COMPOSITE STEEL BEAM

2011 ◽  
Vol 76 (668) ◽  
pp. 1847-1854
Author(s):  
Tetsu USAMI ◽  
Hirofumi Kaneko ◽  
Kenji YAMAZAKI ◽  
Nobuo NAKAYAMA ◽  
Takeshi KATAYAMA
Keyword(s):  
Steel Beam ◽  
Composite Steel
Sign in / Sign up

Export Citation Format

Share Document