An investigation of wave-amplitude vacillation using a light-speckle velocity measuring technique

1982 ◽  
Vol 15 (9) ◽  
pp. 911-915 ◽  
Author(s):  
D E Fitzjarrald
Keyword(s):  
Wave Amplitude ◽  
Measuring Technique ◽  
Velocity Measuring

A pulsed-wire technique for velocity measurements in highly turbulent flows

1971 ◽  
Vol 49 (4) ◽  
pp. 657-691 ◽  
Author(s):  
L. J. S. Bradbury ◽  
I. P. Castro
Keyword(s):  
Turbulent Flows ◽  
Time Of Flight ◽  
Measuring Technique ◽  
Velocity Measurements ◽  
Heated Air ◽  
Resistance Thermometers ◽  
Velocity Measuring ◽  
Highly Turbulent Flows ◽  
Flow Reversals

The velocity measuring technique described in this paper consists of measuring the time of flight of a tracer of heated air from an electrically pulsed wire to one of two sensor wires which are operated as resistance thermometers. These sensor wires are at right angles to the pulsed wire and are placed one on either side of the pulsed wire. The instrument may be used in highly turbulent flows including regions in which flow reversals occur. The paper discusses the theoretical behaviour of the probe and the results of some calibration experiments.

Measurement of the Displacement Across a Coincidence Grain Boundary

1977 ◽  
Vol 35 ◽  
pp. 124-125
Author(s):  
J. W. Matthews ◽  
W. M. Stobbs
Keyword(s):  
Grain Boundary ◽  
Grain Boundaries ◽  
Stacking Fault ◽  
The Other ◽  
Measuring Technique ◽  
High Angle ◽  
Twin Boundaries ◽  
Rigid Displacement ◽  
Cubic Crystals ◽  
Lattice Displacement

Many high-angle grain boundaries in cubic crystals are thought to be either coincidence boundaries (1) or coincidence boundaries to which grain boundary dislocations have been added (1,2). Calculations of the arrangement of atoms inside coincidence boundaries suggest that the coincidence lattice will usually not be continuous across a coincidence boundary (3). There will usually be a rigid displacement of the lattice on one side of the boundary relative to that on the other. This displacement gives rise to a stacking fault in the coincidence lattice.Recently, Pond (4) and Smith (5) have measured the lattice displacement at coincidence boundaries in aluminum. We have developed (6) an alternative to the measuring technique used by them, and have used it to find two of the three components of the displacement at {112} lateral twin boundaries in gold. This paper describes our method and presents a brief account of the results we have obtained.

Density Wave Measurements in a Rectangular Clarifier

1983 ◽  
Vol 18 (1) ◽  
pp. 129-150 ◽  
Author(s):  
Mark K. Watson ◽  
R.R. Hudgins ◽  
P.L. Silveston
Keyword(s):  
Power Spectrum ◽  
Internal Wave ◽  
Internal Waves ◽  
Wave Motion ◽  
Wave Amplitude ◽  
Suspended Solids ◽  
Small Volume ◽  
Density Wave ◽  
Measure Concentration ◽  
Wave Measurements

Abstract Internal wave motion was studied in a laboratory rectangular, primary clarifier. A photo-extinction device was used as a turbidimeter to measure concentration fluctuations in a small volume within the clarifier as a function of time. The signal from this device was fed to a HP21MX minicomputer and the power spectrum plotted from data records lasting approximately 30 min. Results show large changes of wave amplitude as frequency increases. Two distinct regions occur: one with high amplitudes at frequencies below 0.03 Hz, the second with very small amplitudes appears for frequencies greater than 0.1 Hz. The former is associated with internal waves, the latter with flow-generated turbulence. Depth, velocity in the clarifier and inlet suspended solids influence wave amplitudes and the spectra. A variation with position or orientation of the probe was not detected. Contradictory results were found for the influence of flow contraction baffles on internal wave amplitude.

Sign in / Sign up

Export Citation Format

Share Document