Characterization of the three-dimensional flame-holding mechanism in an industrial oil burner with stereoscopic particle image velocimetry

2001 ◽  
Vol 2 ◽  
pp. N16 ◽  
Author(s):  
Virginia R Palero ◽  
Yuji Ikeda
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Three Dimensional ◽  
Stereoscopic Particle Image Velocimetry ◽  
Industrial Oil ◽  
Image Velocimetry

Stereoscopic Particle Image Velocimetry Analysis of Healthy and Emphysemic Alveolar Sac Models

2011 ◽  
Vol 133 (6) ◽  
Author(s):  
Emily J. Berg ◽  
Risa J. Robinson
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Fluid Motion ◽  
Three Dimensional ◽  
Flow Fields ◽  
Stereoscopic Particle Image Velocimetry ◽  
Recirculating Flow ◽  
Image Velocimetry ◽  
Flow Speeds ◽  
Healthy Lung

Emphysema is a progressive lung disease that involves permanent destruction of the alveolar walls. Fluid mechanics in the pulmonary region and how they are altered with the presence of emphysema are not well understood. Much of our understanding of the flow fields occurring in the healthy pulmonary region is based on idealized geometries, and little attention has been paid to emphysemic geometries. The goal of this research was to utilize actual replica lung geometries to gain a better understanding of the mechanisms that govern fluid motion and particle transport in the most distal regions of the lung and to compare the differences that exist between healthy and emphysematous lungs. Excised human healthy and emphysemic lungs were cast, scanned, graphically reconstructed, and used to fabricate clear, hollow, compliant models. Three dimensional flow fields were obtained experimentally using stereoscopic particle image velocimetry techniques for healthy and emphysematic breathing conditions. Measured alveolar velocities ranged over two orders of magnitude from the duct entrance to the wall in both models. Recirculating flow was not found in either the healthy or the emphysematic model, while the average flow rate was three times larger in emphysema as compared to healthy. Diffusion dominated particle flow, which is characteristic in the pulmonary region of the healthy lung, was not seen for emphysema, except for very small particle sizes. Flow speeds dissipated quickly in the healthy lung (60% reduction in 0.25 mm) but not in the emphysematic lung (only 8% reduction 0.25 mm). Alveolar ventilation per unit volume was 30% smaller in emphysema compared to healthy. Destruction of the alveolar walls in emphysema leads to significant differences in flow fields between the healthy and emphysemic lung. Models based on replica geometry provide a useful means to quantify these differences and could ultimately improve our understanding of disease progression.

Estimation of Turbulent Length Scales at a Turbocharger Inlet Using Particle Image Velocimetry

2021 ◽  
Author(s):  
Deb Banerjee ◽  
Ahmet Selamet ◽  
Rick Dehner
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Operating Conditions ◽  
Stereoscopic Particle Image Velocimetry ◽  
Length Scales ◽  
Image Velocimetry ◽  
Fundamental Understanding ◽  
Compressor Inlet ◽  
Kolmogorov Scale

Abstract Stereoscopic Particle Image Velocimetry measurements are carried out at the inlet of a turbocharger compressor at four different shaft speeds from 80,000 rpm to 140,000 rpm and over the entire range of flow rates from choke to mild surge. This paper describes the procedure used in processing the PIV data leading to the estimates of turbulent length scales – integral, Taylor, and Kolmogorov, to enhance the fundamental understanding and characterization of the compressor inlet flow field. The analysis reveals that at most operating conditions the three different length scales have markedly different magnitudes, as expected, while they have somewhat similar qualitative distributions with respect to the duct radius. For example, at 80,000 rpm and at a flow rate of 15.7 g/s (mild surge), the longitudinal integral length scale is of the order of 15 mm, the Taylor scale is around 0.5 mm, and the Kolmogorov scale is about 10 microns. With the onset of flow reversal, the turbulent kinetic energy and turbulent intensity at the compressor inlet are observed to increase rapidly, while the magnitudes of the Kolmogorov scale and to a certain extent, the Taylor scale are found to decrease suggesting that the increased turbulence gives rise to even smaller flow structures. The variation of length scales with compressor shaft speed has also been studied.

Sign in / Sign up

Export Citation Format

Share Document