scholarly journals Mechanical characteristics and comfort evaluation under pedestrian vertical excitation of a thin-walled cold-formed steel footbridge

2021 ◽  
Vol 1028 ◽  
pp. 012008
Author(s):  
Jing Xu ◽  
Xijun Chen ◽  
Jing Li ◽  
Zeyu Li
Keyword(s):  
Mechanical Characteristics ◽  
Vertical Excitation ◽  
Comfort Evaluation ◽  
Cold Formed Steel ◽  
Thin Walled

scholarly journals Experiment and Design Method on Cold-Formed Thin-Walled Steel Lipped Channel Columns with Slotted Web Holes Under Axial Compression

2017 ◽  
Vol 11 (1) ◽  
pp. 244-257 ◽  
Author(s):  
Xingyou Yao
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Ultimate Strength ◽  
Test Results ◽  
Distortional Buckling ◽  
Steel Columns ◽  
Cold Formed Steel ◽  
Thin Walled ◽  
Shell Finite Element ◽  
The Web

Background: Cold-formed steel structural sections used in the walls of residential buildings and agricultural facilities are commonly C-shaped sections with web holes. These holes located in the web of sections can alter the elastic stiffness and the ultimate strength of a structural member. The objective of this paper is to study the buckling mode and load-carrying capacity of cold-formed thin-walled steel column with slotted web holes. Methods: Compression tests were conducted on 26 intermediate length columns with and without holes. The tested compressive members included four different kinds of holes. For each specimen, a shell finite element Eigen-buckling analysis and nonlinear analysis were also conducted. The influence of the slotted web hole on local and distortional buckling response had also been studied. The comparison on ultimate strength between test results and calculated results using Chinese cold-formed steel specification GB50018-2002, North American cold-formed steel specification AISI S100-2016, and nonlinear Finite Element method was made. Result: Test results showed that the distortional buckling occurred for intermediate columns with slotted holes and the ultimate strength of columns with holes was less than that of columns without holes. The ultimate strength of columns decreased with the increase in transverse width of hole in the cross-section of member. The Finite element analysis results showed that the web holes could influence on the elastic buckling stress of columns. The shell finite element could be used to model the buckling modes and analysis the ultimate strength of members with slotted web holes. The calculated ultimate strength shows that results predicted with AISI S100-2016 and analyzed using finite element method are close to test results. The calculated results using Chinese code are higher than the test results because Chinese code has no provision to calculate the ultimate strength of members with slotted web holes. Conclusion: The calculated method for cold-formed thin-walled steel columns with slotted web holes are proposed based on effective width method in Chinese code. The results calculated using the proposed method show good agreement with test results and can be used in engineering design for some specific cold-formed steel columns with slotted web holes studied in this paper.

scholarly journals Behaviour of thin-walled cold-formed steel members in eccentric compression

2018 ◽  
Author(s):  
Viorel Ungureanu ◽  
Maria Kotełko ◽  
Łukasz Borkowski ◽  
Jan Grudziecki
Keyword(s):  
Eccentric Compression ◽  
Steel Members ◽  
Cold Formed Steel ◽  
Thin Walled

Experimental Investigations on Spot Welded Built-Up Cold-Formed Steel Beams

2018 ◽  
Vol 1146 ◽  
pp. 142-151
Author(s):  
Viorel Ungureanu ◽  
Ioan Both ◽  
Mircea Burca ◽  
Ştefan Benzar ◽  
Thai Hoang Nguyen ◽  
...  
Keyword(s):  
Spot Welding ◽  
Steel Sheet ◽  
Experimental Program ◽  
Experimental Investigations ◽  
Steel Beams ◽  
Technological Solution ◽  
Research Project ◽  
Steel Sheets ◽  
Cold Formed Steel ◽  
Thin Walled

Within the WELLFORMED research project, ongoing at the CEMSIG Research Center of the Politehnica University of Timisoara, a new technological solution was proposed for built-up beams made of corrugated steel sheets for the web and thin-walled cold-formed steel profiles for the flanges, connected by spot welding. The research project integrates an extensive experimental program on such beams, using full scale specimens, to demonstrate the feasibility of the proposed solutions and to assess their performance, followed by numerical simulations to characterize and optimize the connecting details. The present paper presents the results of a large experimental program, on small specimens subjected to shear, consisting of two or three layers of steel sheet connected by spot welding.

Numerical Impact Analysis of Folding-Induced Tubular Thin-walled Energy-dissipating Elements

2021 ◽  
Vol 62 (2) ◽  
pp. 82-92
Author(s):  
Eugenio Ruocco ◽  
Antonia Giovenale ◽  
Danilo Di Giacinto
Keyword(s):  
Energy Dissipation ◽  
Impact Analysis ◽  
Impact Resistance ◽  
Impact Angle ◽  
Galvanized Steel ◽  
Absorption Mechanism ◽  
Induced Folding ◽  
Cold Formed Steel ◽  
Thin Walled ◽  
Scale Experiment

This paper deals with the numerical impact analysis of tubular thin-walled steel-made elements with induced folding for energy dissipation application. The excellent deceleration of the impacting mass of axial collapsing structures favors their use in energy dissipation applications, such as impact resistance and rockfall protection. Dynamic Finite Element analyses have been carried out to evaluate the performance of vertical assemblies of cold-formed steel cell-shaped elements welded on each other to form collapsible tubular elements. In turn, these have been gathered in groups and restrained by galvanized steel wires to create modules. The axial collapse, which is the most effective energy absorption mechanism, has been triggered by shaping the elements' edge as serpentine. In the analysis, several assembly configurations have been subjected to a freefall rhombicuboctahedron-shaped rigid block impact; Falling height, impact angle, and block mass have been varied to investigate their effect on the performance. The numerical results show a good agreement when compared to those obtained through a real-scale experiment.

Sign in / Sign up

Export Citation Format

Share Document