Influence of Unsteady Wake on Heat Transfer Coefficient From a Gas Turbine Blade

1993 ◽  
Vol 115 (4) ◽  
pp. 904-911 ◽  
Author(s):  
J.-C. Han ◽  
L. Zhang ◽  
S. Ou
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Gas Turbine ◽  
Strouhal Number ◽  
Turbine Blade ◽  
Surface Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Unsteady Wake ◽  
Wake Passing

The effect of unsteady wake on surface heat transfer coefficients of a gas turbine blade was experimentally determined using a spoked wheel type wake generator. The experiments were performed with a five-airfoil linear cascade in a low-speed wind tunnel facility. The cascade inlet Reynolds number based on the blade chord was varied from 1 to 3 × 105. The wake Strouhal number was varied between 0 and 1.6 by changing the rotating wake passing frequency (rod speed and rod number), rod diameter, and cascade inlet velocity. A hot-wire anemometer system was located at the cascade inlet to detect the instantaneous velocity, phase-averaged mean velocity, and turbulence intensity induced by the passing wake. A thin foil thermocouple instrumented blade was used to determine the surface heat transfer coefficients. The results show that the unsteady passing wake promotes earlier and broader boundary layer transition and causes much higher heat transfer coefficients on the suction surface, whereas the passing wake also significantly enhances heat transfer coefficients on the pressure surface. The blade heat transfer coefficients for a given Reynolds number flow increase with the wake Strouhal number by increasing the rod speed, rod number, or rod diameter. For a given wake passing frequency and rod diameter, the blade heat transfer coefficients decrease with decreasing Reynolds number, although the corresponding wake Strouhal number is increased. The results suggest that both the Reynolds and Strouhal numbers are important parameters in determining the blade heat transfer coefficients in unsteady wake flow conditions.

Unsteady Wake Effect on Film Effectiveness and Heat Transfer Coefficient From a Turbine Blade With One Row of Air and CO2 Film Injection

1994 ◽  
Vol 116 (4) ◽  
pp. 921-928 ◽  
Author(s):  
S. Ou ◽  
J. C. Han
Keyword(s):  
Heat Transfer ◽  
Strouhal Number ◽  
Turbine Blade ◽  
Density Ratio ◽  
Transfer Coefficients ◽  
Suction Surface ◽  
Wake Effect ◽  
Pressure Surface ◽  
Heat Transfer Coefficients ◽  
Unsteady Wake

The effect of unsteady wake and film injection on heat transfer coefficients and film effectiveness from a gas turbine blade was found experimentally. A spoked wheel type wake generator produced the unsteady flow. Experiments were done with a five airfoil linear cascades in a low-speed wind tunnel at a chord Reynolds number of 3 × 105, two wake Strouhal numbers of 0.1 and 0.3, and a no-wake case. A model turbine blade injected air or CO2 through one row of film holes each on the pressure and suction surfaces. The results show that the large-density injectant (CO2) causes higher heat transfer coefficients on the suction surface and lower heat transfer coefficients on the pressure surface. At the higher blowing ratios of 1.0 and 1.5, the film effectiveness increases with increasing injectant-to-mainstream density ratio at a given Strouhal number. However, the density ratio effect on film effectiveness is reversed at the lowest blowing ratio of 0.5. Higher wake Strouhal numbers enhance the heat transfer coefficients but reduce film effectiveness for both density ratio injectants at all three blowing ratios. The effect of the wake Strouhal number on the heat transfer coefficients on the suction surface is greater than that on the pressure surface.

Effect of Unsteady Wake With Trailing Edge Coolant Ejection on Film Cooling Performance for a Gas Turbine Blade

1998 ◽  
Author(s):  
Hui Du ◽  
Srinath V. Ekkad ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Film Cooling ◽  
Surface Heat ◽  
Blade Surface ◽  
Transfer Coefficients ◽  
Trailing Edge ◽  
Surface Heat Transfer ◽  
Heat Transfer Coefficients ◽  
Unsteady Wake

The effect of unsteady wakes with trailing edge coolant ejection on surface heat transfer coefficients and film cooling effectiveness is presented for a downstream film-cooled turbine blade. The detailed heat transfer coefficient and film effectiveness distributions on the blade surface are obtained using a transient liquid crystal technique. Unsteady wakes are produced by a spoked wheel-type wake generator upstream of the five-blade linear cascade. The coolant jet ejection is simulated by ejecting coolant through holes on the hollow spokes of the wake generator. For a blade without film holes, unsteady wake increases both pressure side and suction side heat transfer levels due to early boundary layer transition. Adding trailing edge ejection to the unsteady wake further enhances the blade surface heat transfer coefficients particularly near the leading edge region. For a film-cooled blade, unsteady wake effects slightly enhance surface heat transfer coefficients but significantly reduces film effectiveness. Addition of trailing edge ejection to the unsteady wake has a small effect on surface heat transfer coefficients compared to other significant parameters such as film injection, unsteady wakes, and grid generated turbulence, in that order. Trailing edge ejection effect on film effectiveness distribution is stronger than on the heat transfer coefficients.

Influence of Mainstream Turbulence on Heat Transfer Coefficients From a Gas Turbine Blade

1994 ◽  
Vol 116 (4) ◽  
pp. 896-903 ◽  
Author(s):  
L. Zhang ◽  
J.-C. Han
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Gas Turbine ◽  
Surface Heat ◽  
Transfer Coefficients ◽  
Suction Surface ◽  
Heat Transfer Coefficients ◽  
The Heat Transfer Coefficient

The influence of mainstream turbulence on surface heat transfer coefficients of a gas turbine blade was studied. A five-blade linear cascade in a low-speed wind tunnel facility was used in the experiments. The mainstream Reynolds numbers were 100,000, 200,000, and 300,000 based on the cascade inlet velocity and blade chord length. The grid-generated turbulence intensities at the cascade inlet were varied between 2.8 and 17 percent. A hot-wire anemometer system measured turbulence intensities, mean and time-dependent velocities at the cascade inlet, outlet, and several locations in the middle of the flow passage. A thin-foil thermocouple instrumented blade determined the surface heat transfer coefficients. The results show that the mainstream turbulence promotes earlier and broader boundary layer transition, causes higher heat transfer coefficients on the suction surface, and significantly enhances the heat transfer coefficient on the pressure surface. The onset of transition on the suction surface boundary layer moves forward with increased mainstream turbulence intensity and Reynolds number. The heat transfer coefficient augmentations and peak values on the suction and pressure surfaces are affected by the mainstream turbulence and Reynolds number.

Effect of Unsteady Wake With Trailing Edge Coolant Ejection on Film Cooling Performance for a Gas Turbine Blade

1999 ◽  
Vol 121 (3) ◽  
pp. 448-455 ◽  
Author(s):  
H. Du ◽  
S. V. Ekkad ◽  
J.-C. Han
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Film Cooling ◽  
Surface Heat ◽  
Blade Surface ◽  
Transfer Coefficients ◽  
Trailing Edge ◽  
Surface Heat Transfer ◽  
Heat Transfer Coefficients ◽  
Unsteady Wake

The effect of unsteady wakes with trailing edge coolant ejection on surface heat transfer coefficients and film cooling effectiveness is presented for a downstream film-cooled turbine blade. The detailed heat transfer coefficient and film effectiveness distributions on the blade surface are obtained using a transient liquid crystal technique. Unsteady wakes are produced by a spoked wheel-type wake generator upstream of the five-blade linear cascade. The coolant jet ejection is simulated by ejecting coolant through holes on the hollow spokes of the wake generator. For a blade without film holes, unsteady wake increases both pressure side and suction side heat transfer levels due to early boundary layer transition. Adding trailing edge ejection to the unsteady wake further enhances the blade surface heat transfer coefficients particularly near the leading edge region. For a film-cooled blade, unsteady wake effects slightly enhance surface heat transfer coefficients but significantly reduces film effectiveness. Addition of trailing edge ejection to the unsteady wake has a small effect on surface heat transfer coefficients compared to other significant parameters such as film injection, unsteady wakes, and grid generated turbulence, in that order. Trailing edge ejection effect on film effectiveness distribution is stronger than on the heat transfer coefficients.

Heat Transfer Coefficients and Film Cooling Effectiveness on the Squealer Tip of a Gas Turbine Blade

2003 ◽  
Vol 125 (4) ◽  
pp. 648-657 ◽  
Author(s):  
Jae Su Kwak ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Rotor Blade ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio

Experimental investigations were performed to measure the detailed heat transfer coefficients and film cooling effectiveness on the squealer tip of a gas turbine blade in a five-bladed linear cascade. The blade was a two-dimensional model of a first stage gas turbine rotor blade with a profile of the GE-E3 aircraft gas turbine engine rotor blade. The test blade had a squealer (recessed) tip with a 4.22% recess. The blade model was equipped with a single row of film cooling holes on the pressure side near the tip region and the tip surface along the camber line. Hue detection based transient liquid crystals technique was used to measure heat transfer coefficients and film cooling effectiveness. All measurements were done for the three tip gap clearances of 1.0%, 1.5%, and 2.5% of blade span at the two blowing ratios of 1.0 and 2.0. The Reynolds number based on cascade exit velocity and axial chord length was 1.1×106 and the total turning angle of the blade was 97.9 deg. The overall pressure ratio was 1.2 and the inlet and exit Mach numbers were 0.25 and 0.59, respectively. The turbulence intensity level at the cascade inlet was 9.7%. Results showed that the overall heat transfer coefficients increased with increasing tip gap clearance, but decreased with increasing blowing ratio. However, the overall film cooling effectiveness increased with increasing blowing ratio. Results also showed that the overall film cooling effectiveness increased but heat transfer coefficients decreased for the squealer tip when compared to the plane tip at the same tip gap clearance and blowing ratio conditions.

scholarly journals Effect of Discrete Ribs on Heat Transfer and Friction Inside Narrow Rectangular Cross Section Cooling Passage of Gas Turbine Blade

2021 ◽  
Vol 10 (6) ◽  
pp. 192-209
Author(s):  
Karthik Krishnaswamy ◽  
◽  
Srikanth Salyan ◽  
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Turbine Blades ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Hydraulic Diameter ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Cooling Passage

The performance of a gas turbine during the service life can be enhanced by cooling the turbine blades efficiently. The objective of this study is to achieve high thermohydraulic performance (THP) inside a cooling passage of a turbine blade having aspect ratio (AR) 1:5 by using discrete W and V-shaped ribs. Hydraulic diameter (Dh) of the cooling passage is 50 mm. Ribs are positioned facing downstream with angle-of-attack (α) of 30° and 45° for discrete W-ribs and discerte V-ribs respectively. The rib profiles with rib height to hydraulic diameter ratio (e/Dh) or blockage ratio 0.06 and pitch (P) 36 mm are tested for Reynolds number (Re) range 30000-75000. Analysis reveals that, area averaged Nusselt numbers of the rib profiles are comparable, with maximum difference of 6% at Re 30000, which is within the limits of uncertainty. Variation of local heat transfer coefficients along the stream exhibited a saw tooth profile, with discrete W-ribs exhibiting higher variations. Along spanwise direction, discrete V-ribs showed larger variations. Maximum variation in local heat transfer coefficients is estimated to be 25%. For experimented Re range, friction loss for discrete W-ribs is higher than discrete-V ribs. Rib profiles exhibited superior heat transfer capabilities. The best Nu/Nuo achieved for discrete Vribs is 3.4 and discrete W-ribs is 3.6. In view of superior heat transfer capabilities, ribs can be deployed in cooling passages near the leading edge, where the temperatures are very high. The best THPo achieved is 3.2 for discrete V-ribs and 3 for discrete W-ribs at Re 30000. The ribs can also enhance the power-toweight ratio as they can produce high thermohydraulic performances for low blockage ratios.

scholarly journals Detailed Film Cooling Measurements over a Gas Turbine Blade Using a Transient Liquid Crystal Image Technique

2001 ◽  
Vol 7 (6) ◽  
pp. 415-424 ◽  
Author(s):  
Hui Du ◽  
Srinath V. Ekkad ◽  
Je-Chin Han ◽  
C. Pang Lee
Keyword(s):  
Heat Transfer ◽  
Liquid Crystal ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Gas Turbine Blade ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio ◽  
Image Technique

Detailed heat transfer coefficient and film effectiveness distributions over a gas turbine blade with film cooling are obtained using a transient liquid crystal image technique. The test blade has three rows of film holes on the leading edge and two rows each on the pressure and suction surfaces. A transient liquid crystal technique maps the entire blade midspan region, and helps provide detailed measurements, particularly near the film hole. Tests were performed on a five-blade linear cascade in a low-speed wind tunnel. The mainstream Reynolds number based on cascade exit velocity is5.3×105. Two different coolants (air andCo2) were used to simulate coolant density effect. Coolant blowing ratio was varied between 0.8 and 1.2 for air injection and 0.4–1.2 forCo2injection. Results show that film injection promotes earlier laminar-turbulent boundary layer transition on the suction surface and also enhances local heat transfer coefficients (up to 80%) downstream of injection. An increase in coolant blowing ratio produces higher heat transfer coefficients for both coolants. This effect is stronger immediately downstream of injection holes. Film effectiveness is highest at a blowing ratio of 0.8 for air injection and at a blowing ratio of 1.2 forCo2injection. Such detailed results will help provide insight into the film cooling phenomena on a gas turbine blade.

Heat Transfer Coefficient and Film-Cooling Effectiveness on the Squealer Tip of a Gas Turbine Blade

2002 ◽  
Author(s):  
Jae Su Kwak ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Rotor Blade ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio

Experimental investigations were performed to measure the detailed heat transfer coefficients and film-cooling effectiveness on the squealer tip of a gas turbine blade in a five-bladed linear cascade. The blade was a 2-dimensional model of a first stage gas turbine rotor blade with a profile of the GE-E3 aircraft gas turbine engine rotor blade. The test blade had a squealer (recessed) tip with a 4.22% recess. The blade model was equipped with a single row of film-cooling holes on the pressure-side near the tip region and the tip surface along the camber line. A hue detection based transient liquid crystal technique was used to measure heat transfer coefficients and film-cooling effectiveness. All measurements were done for the tip gap clearances of 1.0%,1.5%, and 2.5% of blade span at the two blowing ratios of 1.0 and 2.0. The Reynolds number based on cascade exit velocity and axial chord length was 1.1 × 106 and the overall pressure ratio was 1.32. The turbulence intensity level at the cascade inlet was 9.7%. Results showed that the overall heat transfer coefficients increased with increasing tip gap clearance, but decreased with increasing blowing ratio. However, the overall film-cooling effectiveness increased with increasing blowing ratio. Results also showed that the overall film-cooling effectiveness increased but heat transfer coefficients decreased for the squealer tip when compared to the plane tip at the same tip gap clearance and blowing ratio conditions.

Combined Effect of Free-Stream Turbulence and Unsteady Wake on Heat Transfer Coefficients From a Gas Turbine Blade

1995 ◽  
Vol 117 (2) ◽  
pp. 296-302 ◽  
Author(s):  
L. Zhang ◽  
J.-C. Han
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Combined Effect ◽  
Transfer Coefficients ◽  
Free Stream Turbulence ◽  
Heat Transfer Coefficients ◽  
Unsteady Wake ◽  
Turbulence Grid

The combined effect of free-stream turbulence and unsteady wakes on turbine blade surface heat transfer was studied. The experiments used a five-blade linear cascade in a low-speed wind tunnel facility. A turbulence grid and spoked-wheel type wake generator produced the free-stream turbulence and unsteady wakes. The mainstream Reynolds numbers based on the cascade inlet mean velocity and blade chord length were 100,000, 200,000, and 300,000. Results show that the blade time-averaged heat transfer coefficient depends on the mean turbulence intensity, regardless of whether this mean turbulence intensity is from unsteady wake only, turbulence grid only, or a wake and grid combination. The higher mean turbulence promotes earlier boundary layer transition and causes much higher heat transfer coefficients on the suction surface. It also significantly enhances the heat transfer coefficients on the pressure surface. The unsteady wake greatly affects blade heat transfer for low oncoming free-stream turbulence; however, the wake effect diminishes for high oncoming turbulence. The free-stream turbulence also strongly affects blade heat transfer for a low wake passing frequency, but the oncoming turbulence effect diminishes for a high unsteady wake condition.

Sign in / Sign up

Export Citation Format

Share Document