scholarly journals Heat Transfer in Rotating Serpentine Passages With Trips Normal to the Flow

1992 ◽  
Vol 114 (4) ◽  
pp. 847-857 ◽  
Author(s):  
J. H. Wagner ◽  
B. V. Johnson ◽  
R. A. Graziani ◽  
F. C. Yeh
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large-scale, multipass, heat transfer model with both radially inward and outward flow. Trip strips on the leading and trailing surfaces of the radial coolant passages were used to produce the rough walls. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, Rossby number, Reynolds number, and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges that are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from stationary and rotating similar models with trip strips. The heat transfer coefficients on surfaces, where the heat transfer increased with rotation and buoyancy, varied by as much as a factor of four. Maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels obtained with the smooth wall model. The heat transfer coefficients on surfaces where the heat transfer decreased with rotation, varied by as much as a factor of three due to rotation and buoyancy. It was concluded that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips and that the effects of rotation were markedly different depending upon the flow direction.

scholarly journals Heat Transfer in Rotating Serpentine Passages With Trips Normal to the Flow

1991 ◽  
Author(s):  
J. H. Wagner ◽  
B. V. Johnson ◽  
R. A. Graziani ◽  
F. C. Yeh
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large scale, multi–pass, heat transfer model with both radially inward and outward flow. Trip strips on the leading and trailing surfaces of the radial coolant passages were used to produce the rough walls. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant–to–wall temperature ratio, Rossby number, Reynolds number and radius–to–passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges which are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from stationary and rotating similar models with trip strips. The heat transfer coefficients on surfaces, where the heat transfer increased with rotation and buoyancy, varied by as much as a factor of four. Maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels obtained with the smooth wall model. The heat transfer coefficients on surfaces, where the heat transfer decreased with rotation, varied by as much as a factor of three due to rotation and buoyancy. It was concluded that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips and that the effects of rotation were markedly different depending upon the flow direction.

scholarly journals Heat Transfer in Rotating Serpentine Passages With Trips Skewed to the Flow

1994 ◽  
Vol 116 (1) ◽  
pp. 113-123 ◽  
Author(s):  
B. V. Johnson ◽  
J. H. Wagner ◽  
G. D. Steuber ◽  
F. C. Yeh
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large-scale, multipass, heat transfer model with both radially inward and outward flow. Trip strips, skewed at 45 deg to the flow direction, were machined on the leading and trailing surfaces of the radial coolant passages. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, rotation number, Reynolds number, and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges that are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from similar stationary and rotating models with smooth walls and with trip strips normal to the flow direction. The heat transfer coefficients on surfaces, where the heat transfer decreased with rotation and buoyancy, decreased to as low as 40 percent of the value without rotation. However, the maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels previously obtained with the smooth wall model. It was concluded that (1) both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips, (2) the effects of rotation are markedly different depending upon the flow direction, and (3) the heat transfer with skewed trip strips is less sensitive to buoyancy than the heat transfer in models with either smooth walls or normal trips. Therefore, skewed trip strips rather than normal trip strips are recommended and geometry-specific tests will be required for accurate design information.

scholarly journals Heat Transfer in Rotating Serpentine Passages With Trips Skewed to the Flow

1992 ◽  
Author(s):  
B. V. Johnson ◽  
J. H. Wagner ◽  
G. D. Steuber ◽  
F. C. Yeh
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large scale, multi-pass, heat transfer model with both radially inward and outward flow. Trip strips, skewed at 45 degrees to the flow direction, were machined on the leading and trailing surfaces of the radial coolant passages. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, rotation number, Reynolds number and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges which are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from similar stationary and rotating models with smooth walls and with trip strips normal to the flow direction. The heat transfer coefficients on surfaces, where the heat transfer decreased with rotation and buoyancy, decreased to as low as 40 percent of the value without rotation. However, the maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels previously obtained with the smooth wall model. It was concluded that (1) both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips, (2) the effects of rotation are markedly different depending upon the flow direction and (3) the heat transfer with skewed trip strips is less sensitivity to buoyancy than the heat transfer in models with either smooth walls or normal trips. Therefore, skewed trip strips rather than normal trip strips are recommended and geometry-specific tests will be required for accurate design information.

Heat Transfer in Rotating Serpentine Passages With Smooth Walls

1991 ◽  
Vol 113 (3) ◽  
pp. 321-330 ◽  
Author(s):  
J. H. Wagner ◽  
B. V. Johnson ◽  
F. C. Kopper
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Vertical Tube ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large-scale, multipass, smooth-wall heat transfer model with both radially inward and outward flow. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, Rossby number, Reynolds number, and radius-to-passage hydraulic diameter ratio. These four parameters were varied over ranges that are typical of advanced gas turbine engine operating conditions. It was found that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs and that the effect of rotation on the heat transfer coefficients was markedly different depending on the flow direction. Local heat transfer coefficients were found to decrease by as much as 60 percent and increase by 250 percent from no-rotation levels. Comparisons with a pioneering stationary vertical tube buoyancy experiment showed reasonably good agreement. Correlation of the data is achieved employing dimensionless parameters derived from the governing flow equations.

scholarly journals Heat Transfer in Rotating Serpentine Passages With Smooth Walls

1990 ◽  
Author(s):  
J. H. Wagner ◽  
B. V. Johnson ◽  
F. C. Kopper
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Vertical Tube ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large scale, multi–pass, smooth–wall heat transfer model with both radially inward and outward flow. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages (coolant–to–wall temperature ratio, Rossby number, Reynolds number and radius–to–passage hydraulic diameter ratio). These four parameters were varied over ranges which are typical of advanced gas turbine engine operating conditions. It was found that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs and that the effect of rotation on the heat transfer coefficients was markedly different depending on the flow direction. Local heat transfer coefficients were found to decrease by as much as 60 percent and increase by 250 percent from no rotation levels. Comparisons with a pioneering stationary vertical tube buoyancy experiment showed reasonably good agreement. Correlation of the data is achieved employing dimensionless parameters derived from the governing flow equations.

Heat Transfer in Rotating Passages With Smooth Walls and Radial Outward Flow

1989 ◽  
Author(s):  
J. H. Wagner ◽  
B. V. Johnson ◽  
T. J. Hajek
Keyword(s):  
Heat Transfer ◽  
Large Scale ◽  
Fluid Dynamic ◽  
Density Ratio ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Turbine Engine ◽  
Heat Transfer Coefficients ◽  
Streamwise Location

Experiments were conducted to determine the effects of rotation on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a smooth wall, large scale heat transfer model. The objective was to obtain the heat transfer data base required to develop heat transfer correlations and to assess computational fluid dynamic techniques for rotating coolant passages. An analysis of the governing equations showed that four parameters influence the heat transfer in rotating passages (coolant density ratio, Rossby number, Reynolds number and radius ratio). These four parameters were varied over ranges which exceed the ranges of current open literature results, but which are typical of current and advanced gas turbine engine operating conditions. Rotation affected the heat transfer coefficients differently for different locations in the coolant passage. For example, heat transfer at some locations increased with rotation, but decreased and then increased again at other locations. Heat transfer coefficients varied by as much as a factor of 5 between the leading and trailing surfaces for the same test condition and streamwise location. Comparisons with previous results are presented.

Heat Transfer in Rotating Passages With Smooth Walls and Radial Outward Flow

1991 ◽  
Vol 113 (1) ◽  
pp. 42-51 ◽  
Author(s):  
J. H. Wagner ◽  
B. V. Johnson ◽  
T. J. Hajek
Keyword(s):  
Heat Transfer ◽  
Large Scale ◽  
Fluid Dynamic ◽  
Density Ratio ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Turbine Engine ◽  
Heat Transfer Coefficients ◽  
Streamwise Location

Experiments were conducted to determine the effects of rotation on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a smooth wall, large-scale heat transfer model. The objective was to obtain the heat transfer data base required to develop heat transfer correlations and to assess computational fluid dynamic techniques for rotating coolant passages. An analysis of the governing equations showed that four parameters influence the heat transfer in rotating passages (coolant density ratio, Rossby number, Reynolds number, and radius ratio). These four parameters were varied over ranges that exceed the ranges of current open literature results, but that are typical of current and advanced gas turbine engine operating conditions. Rotation affected the heat transfer coefficients differently for different locations in the coolant passage. For example, heat transfer at some locations increased with rotation, but decreased and then increased again at other locations. Heat transfer coefficients varied by as much as a factor of five between the leading and trailing surfaces for the same test condition and streamwise location. Comparisons with previous results are presented.

scholarly journals Rotating Heat Transfer Experiments With Turbine Airfoil Internal Flow Passages

1986 ◽  
Author(s):  
Joel H. Wagner ◽  
Jay C. Kim ◽  
Bruce V. Johnson
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Large Scale ◽  
Flow Direction ◽  
Internal Flow ◽  
Operating Conditions ◽  
Coolant Temperature ◽  
Rossby Number ◽  
Transfer Coefficients ◽  
Bulk Fluid

Internal convective cooling is used to maintain acceptable gas turbine rotor blade temperatures. The heat transfer from the blade coolant passage walls is governed by forced convection, Coriolis forces and buoyance due to wall and coolant temperature differences. Currently little data is available to designers regarding the combined effects of these three parameters. To obtain required data, a rotating heat transfer facility was developed for experiments with large scale models and run at rotation and flow parameters typical of current gas turbine operating conditions. Analysis of the equations of motion showed that the perinent nondimensional parameters were Reynolds number, Rossby number, the difference in wall fluid and bulk fluid density and geometric ratios. The models were instrumented to measure average heat transfer rates on the coolant passage wall elements, and with pressure taps for friction data. An initial set of experiments have been conducted with rough wall geometries, typical of those used in blades. Results from the rotating experiments showed large heat transfer coefficient increases and decreases on the coolant passage leading and trailing surfaces compared to nonrotating heat transfer coefficients. The heat transfer was shown to be a function of inward or outward flow direction and Rossby number for the experiments conducted.

A Two-Dimensional Analytical Method for Turbine Blade Cooling Design

2017 ◽  
Author(s):  
Chen Li ◽  
Jian-jun Liu ◽  
Bai-tao An ◽  
Zhi-qiang Yu
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Analytical Method ◽  
Internal Heat ◽  
Transfer Coefficients ◽  
Simple Method ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients ◽  
Blade Cooling ◽  
Cooling Design

Turbine blade cooling design involves many complex fluid-thermal coupling issues. Using complete 3D CFD and FEA method would increase the cost of computing; on the other hand, the simplified 1D analytical method would lose too much important blade geometric information when employed in preliminary cooling design. In order to shorten design period and improve the design efficiency, the current 2D analytical method has been developed from a conceptual design that stacking a series of 2D radial sections to shape a quasi-3D blade model attached with the internal fluid flow network. Each of those 2D radial sections could maximally retain the actual blade profile, thus making it more authentic for accomplishing the numerical calculations of turbine cascade flow and heat transfer. For the gas side, methods for calculating external heat transfer coefficients have been investigated, and a simple method for considering the effect of thermal barrier coating on 2D conduction model is proposed. For internal cooling channels, a general calculation method of compressible pipe flow under rotating condition has been derived for fast solving coolant mass flow rates and internal heat transfer coefficients supported by empirical correlations of Darcy resistance coefficient and Nusselt number. Those work are significant to achieve the parametric cooling design by means of modifying and controlling geometric parameters and boundary conditions. Consequently, a real turbine blade case by applying the current 2D analytical method to obtain a quasi-3D blade temperature distribution is presented, demonstrating that this 2D analytical method is effective for turbine cooling design.

Heat Transfer and Pressure Drop Correlations for Square Channels With 45 Deg Ribs at High Reynolds Numbers

2009 ◽  
Vol 131 (7) ◽  
Author(s):  
Akhilesh P. Rallabandi ◽  
Huitao Yang ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Turbine Blade Cooling ◽  
Square Channel ◽  
Heat Transfer Coefficients ◽  
High Reynolds ◽  
Cooling Passage

Systematic experiments are conducted to measure heat transfer enhancement and pressure loss characteristics on a square channel (simulating a gas turbine blade cooling passage) with two opposite surfaces roughened by 45 deg parallel ribs. Copper plates fitted with a silicone heater and instrumented with thermocouples are used to measure regionally averaged local heat transfer coefficients. Reynolds numbers studied in the channel range from 30,000 to 400,000. The rib height (e) to hydraulic diameter (D) ratio ranges from 0.1 to 0.18. The rib spacing (p) to height ratio (p/e) ranges from 5 to 10. Results show higher heat transfer coefficients at smaller values of p/e and larger values of e/D, though at the cost of higher friction losses. Results also indicate that the thermal performance of the ribbed channel falls with increasing Reynolds numbers. Correlations predicting Nusselt number (Nu) and friction factor (f¯) as a function of p/e, e/D, and Re are developed. Also developed are correlations for R and G (friction and heat transfer roughness functions, respectively) as a function of the roughness Reynolds number (e+), p/e, and e/D.

Sign in / Sign up

Export Citation Format

Share Document