scholarly journals Modeling the Ductile Brittle Fracture Transition in Reactor Pressure Vessel Steels Using a Cohesive Zone Model Based Approach

2013 ◽  
Author(s):  
Pritam Chakraborty ◽  
S. Bulent Biner
Keyword(s):  
Crack Growth ◽  
Pressure Vessel ◽  
Cohesive Zone ◽  
Fracture Behavior ◽  
Cohesive Zone Model ◽  
Pressure Vessels ◽  
Reactor Pressure Vessel ◽  
Zone Model ◽  
Fracture Properties ◽  
Reactor Pressure

Fracture properties of Reactor Pressure Vessel (RPV) steels show large variations with changes in temperature and irradiation levels. Brittle behavior is observed at lower temperatures and/or higher irradiation levels whereas ductile mode of failure is predominant at higher temperatures and/or lower irradiation levels. In addition to such temperature and radiation dependent fracture behavior, significant scatter in fracture toughness has also been observed. As a consequence of such variability in fracture behavior, accurate estimates of fracture properties of RPV steels are of utmost importance for safe and reliable operation of reactor pressure vessels. A cohesive zone based approach is being pursued in the present study where an attempt is made to obtain a unified law capturing both stable crack growth (ductile fracture) and unstable failure (cleavage fracture). The parameters of the constitutive model are dependent on both temperature and failure probability. The effect of irradiation has not been considered in the present study. The use of such a cohesive zone based approach would allow the modeling of explicit crack growth at both stable and unstable regimes of fracture. Also it would provide the possibility to incorporate more physical lower length scale models to predict DBT. Such a multi-scale approach would significantly improve the predictive capabilities of the model, which is still largely empirical.

Failure Probability Assessment for a Boiling Water Reactor Pressure Vessel Under Low Temperature Over-Pressure Event

2012 ◽  
Author(s):  
Hsoung-Wei Chou ◽  
Chin-Cheng Huang ◽  
Bo-Yi Chen ◽  
Hsien-Chou Lin ◽  
Ru-Feng Liu
Keyword(s):  
Low Temperature ◽  
Failure Probability ◽  
Pressure Vessel ◽  
Fracture Probability ◽  
Pressure Vessels ◽  
Reactor Pressure Vessel ◽  
Boiling Water ◽  
Boiling Water Reactor ◽  
Water Reactor ◽  
Reactor Pressure

The fracture probability of a boiling water reactor pressure vessel for a domestic nuclear power plant in Taiwan has been numerically analyzed using an advanced version of ORNL’s FAVOR code. First, a model of the vessel beltline region, which includes all shell welds and plates, is built for the FAVOR code based on the plant specific parameters of the reactor pressure vessel. Then, a novel flaw model which describes the flaw types of surface breaking flaws, embedded weld flaws and embedded plate flaws are simulated along both inner and outer vessel walls. When conducting the fracture probability analyses, a transient low temperature over-pressure event, which has previously been shown to be the most severe challenge to the integrity of boiling water reactor pressure vessels, is considered as the loading condition. It is found that the fracture occurs in the fusion-line area of axial welds, but with only an insignificant failure probability. The low through-wall cracking frequency indicates that the analyzed reactor pressure vessel maintains sufficient stability until either the end-of-license or for doubling of the present license of operation.

Measurements of Stress During Thermal Shock in Clad Reactor Pressure Vessel Material Using Time-Resolved In-Situ Synchrotron X-Ray Diffraction

2018 ◽  
Author(s):  
Sam Oliver ◽  
Chris Simpson ◽  
Andrew James ◽  
Christina Reinhard ◽  
David Collins ◽  
...  
Keyword(s):  
Thermal Shock ◽  
Pressure Vessel ◽  
Pressure Vessels ◽  
Reactor Pressure Vessel ◽  
Pressure Vessel Steel ◽  
X Ray Diffraction ◽  
Time Resolved ◽  
Vessel Steel ◽  
X Ray ◽  
Reactor Pressure

Nuclear reactor pressure vessels must be able to withstand thermal shock due to emergency cooling during a loss of coolant accident. Demonstrating structural integrity during thermal shock is difficult due to the complex interaction between thermal stress, residual stress, and stress caused by internal pressure. Finite element and analytic approaches exist to calculate the combined stress, but validation is limited. This study describes an experiment which aims to measure stress in a slice of clad reactor pressure vessel during thermal shock using time-resolved synchrotron X-ray diffraction. A test rig was designed to subject specimens to thermal shock, whilst simultaneously enabling synchrotron X-ray diffraction measurements of strain. The specimens were extracted from a block of SA508 Grade 4N reactor pressure vessel steel clad with Alloy 82 nickel-base alloy. Surface cracks were machined in the cladding. Electric heaters heat the specimens to 350°C and then the surface of the cladding is quenched in a bath of cold water, representing thermal shock. Six specimens were subjected to thermal shock on beamline I12 at Diamond Light Source, the UK’s national synchrotron X-ray facility. Time-resolved strain was measured during thermal shock at a single point close to the crack tip at a sample rate of 30 Hz. Hence, stress intensity factor vs time was calculated assuming K-controlled near-tip stress fields. This work describes the experimental method and presents some key results from a preliminary analysis of the data.

Accounting for the Effects of Inservice Inspection Flaw Depth Sizing Errors in Developing Flaw Size Distribution Tables

2009 ◽  
Author(s):  
S. R. Gosselin ◽  
F. A. Simonen
Keyword(s):  
Pressure Vessel ◽  
Pressure Vessels ◽  
Reactor Pressure Vessel ◽  
Expert Elicitation ◽  
Flaw Size ◽  
Physical Models ◽  
Asme Code ◽  
Valid Comparison ◽  
Vessel Material ◽  
Reactor Pressure

Probabilistic fracture mechanics studies have addressed reactor pressure vessels that have high levels of material embrittlement. These calculations have used flaw size and density distributions determined from precise and optimized laboratory measurements made and validated with destructive methods as well as from physical models and expert elicitation. The experimental data were obtained from reactor vessel material samples removed from cancelled plants (Shoreham and the Pressure Vessel Research Users Facility (PVRUF)). Consequently, utilities may need to compare the numbers and sizes of reactor pressure vessel flaws identified by the plant’s inservice inspection program to the numbers and sizes of flaws assumed in prior failure probability calculations. This paper describes a method to determine whether the flaws in a particular reactor pressure vessel are consistent with the assumptions regarding the number and sizes of flaws used in other analyses. The approach recognizes that ASME Code Section XI examinations suffer from limitations in terms of sizing errors for very small flaws. Direct comparisons of a vessel specific flaw distribution with other documented flaw distributions would lead to pessimistic conclusions. This paper provides a method for a valid comparison that accounts for flaw sizing errors present in ASME Code Section XI examinations.

Irreversible cyclic cohesive zone model for prediction of mode I fatigue crack growth in CFRP-strengthened steel plates

2020 ◽  
Vol 110 ◽  
pp. 102804
Author(s):  
M. Mohajer ◽  
M. Bocciarelli ◽  
P. Colombi ◽  
A. Hosseini ◽  
A. Nussbaumer ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Cohesive Zone ◽  
Cohesive Zone Model ◽  
Steel Plates ◽  
Mode I ◽  
Zone Model
Sign in / Sign up

Export Citation Format

Share Document