Progressive fatigue behavior of single-lap bolted laminates under different tightening torque magnitudes

2020 ◽  
Vol 234 (10) ◽  
pp. 1303-1312
Author(s):  
M Feyzi ◽  
S Hassanifard ◽  
A Varvani-Farahani
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Fatigue Behavior ◽  
Damage Model ◽  
Three Dimensional ◽  
Bolted Joints ◽  
Element Analysis ◽  
Damage And Failure ◽  
Experienced Fatigue ◽  
Three Dimensional Finite Element

The present paper studies fatigue damage and life of single-lap bolted joints tightened with different torque magnitudes subjected to uniaxial load cycles. The adherends were constructed from E-glass/epoxy layers using a hand layup technique and assembled by 1.5, 3, and 8 N m of applied torques. Increasing the torque magnitude benefitted the final fatigue life of the joints so that the high-cycle fatigue life of the joint sample tightened with 8 N m was as high as 10 times that of the joint tightened with 1.5 N m. In the numerical section of this study, a three-dimensional finite element analysis was employed, and the impacts of applied torques were included in the progressive damage model to assess damage and failure in the bolted joints. For the joints tightened with higher torque levels, numerical results revealed higher fatigue lives but at the cost of more delamination at the vicinity of the hole. Laminate fracture surface was investigated through scanning electron microscopy and more cracking/damage progress was evidenced in matrix, fiber, and matrix–fiber interface as composite joints experienced fatigue cycles. Experimental life data of tested joints agreed with those anticipated through the use of finite element analyses indicating the developed model as an appropriate tool in evaluating the effects of applied torques on the fatigue fracture behavior of bolted laminates.

Load Transfer Analysis of Cracked Bolted Joints

2010 ◽  
Vol 118-120 ◽  
pp. 147-150
Author(s):  
Da Zhao Yu ◽  
Yue Liang Chen ◽  
Yong Gao ◽  
Wen Lin Liu ◽  
Zhong Hu Jia
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Load Transfer ◽  
Three Dimensional ◽  
Element Model ◽  
Bolted Joints ◽  
Bolted Joint ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

Three-dimensional finite element model of a cracked bolted joint has been developed in the non-linear finite element code MSC.Marc and attempts were made to validate it by comparing results with those of experiments and other finite element. Issues in modeling the contact between the joint parts, which affect the accuracy and efficiency of the model, were presented. Experimental measurements of load transfer were compared with results from finite element analysis. The results show that three-dimensional finite element model of cracked bolted joint can produce results in close agreement with experiment. Three-dimensional effects such as bolt titling, seconding and through-thickness variations in stress and strain are well represented by such models. Three-dimensional finite element analysis was also used to study the effects of hole mod and crack on the load transfer behaviour of single lap bolted joints. The results show that hole mode has big effect on load transfer of cracked bolted joint. In the whole progress of crack growth, the load transfer through bolt 1 decrease, and almost all of the load duduction of bolt 1 transfer into blot 2 rather than into bolt 3.

Parametric Analysis Mechanical Properties of Bolted Joints

2010 ◽  
Vol 97-101 ◽  
pp. 3924-3927 ◽  
Author(s):  
Da Zhao Yu ◽  
Yue Liang Chen ◽  
Zhong Hu Jia ◽  
Yong Gao ◽  
Wen Lin Liu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Bolted Joints ◽  
Bolted Joint ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

Three-dimensional finite element model of a bolted joint has been developed in the non-linear finite element code MSC.Marc and attempts were made to validate it by comparing results with those of experiments and other finite element. Issues in modeling the contact between the joint parts, which affect the accuracy and efficiency of the model, were presented. Experimental measurements of surface strains and load transfer ratio(LTR) were compared with results from finite element analysis. The results show that three-dimensional finite element model of bolted joint can produce results in close agreement with experiment. Three-dimensional effects such as bolt titling, seconding and through-thickness variations in stress and strain are well represented by such models. Three-dimensional finite element analysis was also used to study the effects of different parameters on the mechanical behaviour of single lap bolted joints. The results show that straight hole, small bolt diameter, and big hole pitch are selected first for bolted joint if other conditions allowed, and effect of bolt material on LTR of joint is small for small load. Interference and pre-stress should be strictly controlled for bolted joints in order to attain the best fatigue capability of lap joint.

The Finite Element Analysis on High Duty Bolted Joints of Slewing Bearing

2011 ◽  
Vol 121-126 ◽  
pp. 1564-1569
Author(s):  
Xin Wang ◽  
Xue Xia Liu ◽  
Xu Yang Cao ◽  
Feng Zhou ◽  
Yang Zhou ◽  
...  
Keyword(s):  
Finite Element ◽  
Plate Thickness ◽  
Three Dimensional ◽  
Element Model ◽  
Bolted Joints ◽  
Reasonable Assumption ◽  
Element Analysis ◽  
Slewing Bearing ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

By reasonable assumption and considering the friction, contact, preload intensity, load eccentricity, bolt bending, and other nonlinear factors, we establish three-dimensional finite element model for the high duty bolted joint to reflect the bolt behavior and develop the finite element calculation method for static strength, fatigue strength and related stresses of bolt. By this method, we do numerous numerical simulation experiments to study the effects of preload intensity, support plate thickness on the bolt behavior. These results will guide designer to complete the slewing bearing design effectively and accurately, and these research ideas can be well applied to bolted joints study in other devices.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

Sign in / Sign up

Export Citation Format

Share Document