Volumetric radiative heat transfer in participating media near solids for large temperature gradient

2021 ◽  
Author(s):  
SABER HAMIMID ◽  
Messaoud Guellal ◽  
madiha bouafia
Keyword(s):  
Heat Transfer ◽  
Temperature Gradient ◽  
Radiative Heat Transfer ◽  
Radiative Heat ◽  
Large Temperature ◽  
Participating Media ◽  
Large Temperature Gradient

A new approach for solving radiative heat transfer in non-participating media

2020 ◽  
Author(s):  
Chandler Klüser Chantre ◽  
Maurício Ferreira ◽  
GUENTHER Krieger Filho
Keyword(s):  
Heat Transfer ◽  
Radiative Heat Transfer ◽  
Radiative Heat ◽  
Participating Media ◽  
New Approach

CFD Modeling of Cogeneration Burner Applications and the Significance of Thermal Radiative Heat Transfer Effects

2003 ◽  
Author(s):  
A. F. Tenbusch
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Thermal Radiation ◽  
System Design ◽  
Radiative Heat Transfer ◽  
Radiative Heat ◽  
Flow Distribution ◽  
Cfd Modeling ◽  
Large Temperature ◽  
Flow Heat

Industrial burners provide process heat for a wide range of applications including cogeneration power production. In such applications a (typically) natural gas fired stationary turbine powers an electric generator and indirectly powers a heat recover steam generator (HRSG). The HRSG steam cycle operates by reclaiming the residual thermal energy of the gas turbine exhaust (GTE) flow. Burners are used to reheat the GTE and increase plant capacity during peak demand periods. CFD modeling is used in the design of burner systems for HRSG applications. GTE flow exiting the turbine unit is passed through a diffuser and then expanded into ductwork where the steam system heat exchangers are located. The expansion of the GTE flow from the turbine diffuser to the full cross section of the ductwork is usually severe and creates an uneven flow distribution. Flow correcting structure may be needed to distribute the flow depending upon the severity of the duct expansion. CFD modeling is used to predict the flow distribution of the GTE and guide the design of any necessary flow correcting structure. Burners are typically installed in an array upstream of the application heat exchanger inlet. CFD combustion, heat transfer, and flow analysis is employed in the burner system design process to locate the burner array, determine any necessary flow baffling, and to ensure and provide a uniform thermal distribution at the downstream heat exchanger inlet. Excessive thermal variation in the GTE flow entering the heat exchanger results in large temperature gradients that can lead to thermal cracking and fatigue of the heat exchanger surfaces. CFD modeling is used to ensure that the burner system design produces a uniform flow and temperature distribution at the heat exchanger inlet region downstream of the burners. This report presents a case study of a CFD flow, heat-transfer, and combustion analysis for a typical HRSG burner application. Two CFD models were constructed for the analysis. The first model included the coupled effects of flow, heat transfer, and combustion for the entire HRSG model volume, but excluded the effects of thermal radiation. The second model included a sub-domain of the HRSG volume near the burner and included the additional effects of thermal radiation, both surface radiation and the effects of the radiatively participating flue gas. Radiative effects were included in the second model by employing the Discrete Transfer Method. Results of the study showed the significant role thermal radiative heat transfer had on the resulting temperature predictions downstream of the flame zone.

Accelerate Iteration of Least-Squares Finite Element Method for Radiative Heat Transfer in Participating Media With Diffusely Reflecting Walls

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Wei An ◽  
Tong Zhu ◽  
NaiPing Gao
Keyword(s):  
Heat Transfer ◽  
Finite Element Method ◽  
Boundary Condition ◽  
Finite Element ◽  
Radiative Transfer ◽  
Radiative Heat Transfer ◽  
Radiative Heat ◽  
Present Model ◽  
Participating Media ◽  
Element Method

A high reflectivity of walls often leads to prohibitive computation time in the numerical simulation of radiative heat transfer. Such problem becomes very serious in many practical applications, for example, metal processing in high-temperature environment. The present work proposes a modified diffusion synthetic acceleration model to improve the convergence of radiative transfer calculation in participating media with diffusely reflecting boundary. This model adopts the P1 diffusion approximation to rectify the scattering source term of radiative transfer equation and the reflection term of the boundary condition. The corrected formulation for boundary condition is deduced and the algorithm is realized by finite element method. The accuracy of present model is verified by comparing the results with those of Monte Carlo method and finite element method without any accelerative technique. The effects of emissivity of walls and optical thickness on the convergence are investigated. The results indicate that the accuracy of present model is reliable and its accelerative effect is more obvious for the optically thick and scattering dominated media with intensive diffusely reflecting walls.

Sign in / Sign up

Export Citation Format

Share Document