Constrained Liners Implanted Simultaneously at the Time of Acetabular Shell Revision with a Highly Porous Implant

2020 ◽  
Vol 102 (17) ◽  
pp. 1521-1529 ◽  
Author(s):  
Nicholas A. Bedard ◽  
Timothy S. Brown ◽  
David G. Lewallen ◽  
Robert T. Trousdale ◽  
Daniel J. Berry ◽  
...  
Orthopedics ◽  
2017 ◽  
Vol 41 (1) ◽  
pp. e154-e157 ◽  
Author(s):  
Nipun Sodhi ◽  
Timothy Izant ◽  
John Diana ◽  
Daniel Del Gaizo ◽  
Michael Baratz ◽  
...  

Author(s):  
Steven D. Toteda

Zirconia oxygen sensors, in such applications as power plants and automobiles, generally utilize platinum electrodes for the catalytic reaction of dissociating O2 at the surface. The microstructure of the platinum electrode defines the resulting electrical response. The electrode must be porous enough to allow the oxygen to reach the zirconia surface while still remaining electrically continuous. At low sintering temperatures, the platinum is highly porous and fine grained. The platinum particles sinter together as the firing temperatures are increased. As the sintering temperatures are raised even further, the surface of the platinum begins to facet with lower energy surfaces. These microstructural changes can be seen in Figures 1 and 2, but the goal of the work is to characterize the microstructure by its fractal dimension and then relate the fractal dimension to the electrical response. The sensors were fabricated from zirconia powder stabilized in the cubic phase with 8 mol% percent yttria. Each substrate was sintered for 14 hours at 1200°C. The resulting zirconia pellets, 13mm in diameter and 2mm in thickness, were roughly 97 to 98 percent of theoretical density. The Engelhard #6082 platinum paste was applied to the zirconia disks after they were mechanically polished ( diamond). The electrodes were then sintered at temperatures ranging from 600°C to 1000°C. Each sensor was tested to determine the impedance response from 1Hz to 5,000Hz. These frequencies correspond to the electrode at the test temperature of 600°C.


Author(s):  
Ian M. Anderson ◽  
Arnulf Muan ◽  
C. Barry Carter

Oxide mixtures which feature a coexistence of phases with the wüstite and spinel structures are considered model systems for the study of solid-state reaction kinetics, phase boundaries, and thin-film growth, and such systems are especially suited to TEM studies. (In this paper, the terms “wüstite” and “spinel” will refer to phases of those structure types.) The study of wüstite-spinel coexistence has been limited mostly to systems near their equilibrium condition, where the assumptions of local thermodynamic equilibrium are valid. The cation-excess spinels of the type Ni2(1+x)Ti1-xO4, which reportedly exist only above 1375°C4, provide an excellent system for the study of wüstite-spinel coexistence under highly nonequilibrium conditions. The nature of these compounds has been debated in the literature. X-ray and neutron powder diffraction patterns have been used to advocate the existence of a single-phase, non- stoichiometric spinel. TEM studies of the microstructure have been used to suggest equilibrium coexistence of a stoichiometric spinel, Ni2TiO4, and a wüstite phase; this latter study has shown a coexistence of wüstite and spinel phases in specimens thought to have been composed of a single, non- stoichiometric spinel phase. The microstructure and nature of this phase coexistence is the focus of this study. Specimens were prepared by ball-milling a mixture of NiO and TiO2 powders with 10 wt.% TiO2. The mixture was fired in air at 1483°C for 5 days, and then quenched to room temperature. The aggregate thus produced was highly porous, and needed to be infiltrated prior to TEM sample preparation, which was performed using the standard techniques of lapping, dimpling, and ion milling.


2004 ◽  
Vol 46 (5) ◽  
pp. 243-247
Author(s):  
Wolfram Harbich ◽  
Udo Mücke ◽  
Georg Berger

2020 ◽  
Vol 67 (1) ◽  
pp. 148-155
Author(s):  
Anatoliy V. Fedotov ◽  
Viktor S. Grigoriev ◽  
Dmitriy A. Kovalev ◽  
Andrey A. Kovalev

To speed up the wastewater treatment under aerobic conditions and to optimize the processes of anaerobic wastewater treatment in digesters, immobilization technologies of microorganisms and enzymes on solid carriers are used. Ceramic carriers based on aluminosilicates and alumina are one of the promising inorganic biomass carriers. (Research purpose) To study the structure of porous ceramic biomass carriers for anaerobic processing of organic waste and evaluate the prospects for their use. (Materials and methods) The substrate for anaerobic digestion was a mixture of sediments of the primary and secondary sewage sumps of the Lyubertsy treatment facilities. K-65 cattle feed was used to ensure the constancy of the composition of organic substances in substrates as a cosubstrate. The authors used the method of low-temperature nitrogen adsorption of Bruner-Emmett-Teller to study the pore structure and specific surface of solid carriers on a specific surface analyzer Quntachrome Autosorb-1. (Results and discussion) The main characteristics (specific surface, volume of micro- and mesopores, predominant pore radius, water absorption and others) of chamotte foam lightweight and highly porous corundum ceramics were determined. It was revealed that ceramic materials with a developed surface and electrically conductive material provided an increase in biogas yield by 3.8-3.9 percent with an increase in methane content by an average of 5 percent. (Conclusions) The results of anaerobic digestion showed a positive effect of both a conductive carrier and highly porous ceramic materials on the process of anaerobic bioconversion of organic waste into biogas. It is advisable to expand experimental studies on the use of a conductive carrier with a developed surface based on highly porous ceramics.


Sign in / Sign up

Export Citation Format

Share Document