scholarly journals Performance of SwiftScan planar and single photon emission computed tomography technology using low-energy high-resolution and sensitivity collimator

2020 ◽  
Author(s):  
Takayuki Shibutani ◽  
Masahisa Onoguchi ◽  
Hiroto Yoneyama ◽  
Takahiro Konishi ◽  
Kenichi Nakajima
Keyword(s):  
High Resolution ◽  
Spatial Resolution ◽  
Single Photon ◽  
Photon Emission ◽  
High Sensitivity ◽  
Low Energy ◽  
Emission Computed Tomography ◽  
System Sensitivity ◽  
Photon Emission Computed Tomography ◽  
Spect System

Abstract Background A new low-energy high-resolution-sensitivity (LEHRS) collimator was developed by General Electric Healthcare. SwiftScan planar and SPECT system using LEHRS collimator were formulated to achieve the low-dose and/or short-term acquisition. We demonstrated the performance of SwiftScan planar and SPECT system with LEHRS collimator using phantoms. Methods Line source, cylindrical and flat plastic dish phantoms were used to evaluate the performance of planar and SPECT images for four patterns of Siemens LEHR, GE LEHR, GE LEHRS and SwiftScan using two SPECT-CT scanners. Each phantom was filled with 99mTc solution, and the spatial resolution, sensitivity and image uniformity were calculated from the planar and SPECT data. Results The full-width at half maximum (FWHM) values as system spatial resolution of Siemens LEHR, GE LEHR and GE LEHRS were 7.3, 7.5 and 7.3 mm, respectively. GE LEHRS showed the lower FWHM value by increasing the blend ratio in Clarity 2D processing. The system sensitivities of Siemens LEHR, GE LEHR and GE LEHRS were 88.4, 67.6 and 89.8 cps/MBq, respectively. The system sensitivity of GE LEHRS increased by approximately 30% compared with that of GE LEHR and was similar to that of Siemens LEHR. The FWHM values of SPECT with an FBP method were 10.3, 10.4, 10.4 and 10.3 mm (p = n.s.). The FWHM values of the OSEM method were better with an increase in iteration values. The differential uniformities of Siemens LEHR, GE LEHR, GE LEHRS and GE SwiftScan were 15.3%, 15.1%, 15.4% and 14.6%, respectively, using the FBP method. The differential uniformity of OSEM method was higher with an increase in iteration value. Conclusion The SwiftScan planar and SPECT have a high sensitivity while maintaining the spatial resolution compared with the conventional system.

scholarly journals Performance Evaluation of Fifth-Generation Ultra-High-Resolution SPECT System with Two Stationary Detectors and Multi-Pinhole Imaging

2020 ◽  
Author(s):  
Jan V Hoffmann ◽  
Jan P Janssen ◽  
Takayuki Kanno ◽  
Takayuki Shibutani ◽  
Masahisa Onoguchi ◽  
...  
Keyword(s):  
High Resolution ◽  
Spatial Resolution ◽  
Single Photon ◽  
Photon Emission ◽  
Small Animal ◽  
High Sensitivity ◽  
General Purpose ◽  
Emission Computed Tomography ◽  
High Count ◽  
Spect System

Abstract Background: Small-animal single-photon emission computed tomography (SPECT) systems with multi-pinhole collimation and large stationary detectors have advantages compared to systems with moving small detectors. These systems benefit from less labour-intensive maintenance and quality control as fewer prone parts are moving, higher accuracy for focused scans and maintaining high resolution with increased sensitivity due to focused pinholes on the field of view. This study aims to investigate the performance of a novel ultra-high-resolution scanner with two-detector-configuration (U-SPECT5-E) and to compare its image quality to a conventional micro-SPECT system with three stationary detectors (U-SPECT+).Methods: The new U-SPECT5-E with two stationary detectors was used for acquiring data with 99mTc-filled point source, hot-rod and uniformity phantoms to analyse sensitivity, spatial resolution, uniformity and contrast-to-noise ratio (CNR). Three dedicated multi-pinhole mouse collimators with 75 pinholes each and 0.25-, 0.60- and 1.00-mm pinholes for extra ultra-high resolution (XUHR-M), general-purpose (GP-M) and ultra-high sensitivity (UHS-M) imaging were examined. For CNR analysis, four different activity ranges representing low- and high-count settings were investigated for all three collimators. The experiments for the performance assessment were repeated with the same GP-M collimator in the three-detector U-SPECT+ for comparison. Results: Peak sensitivity was 237 cps/MBq (XUHR-M), 847 cps/MBq (GP-M), 2054 cps/MBq (UHS-M) for U-SPECT5-E and 1710 cps/MBq (GP-M) for U-SPECT+. In the visually analysed sections of the reconstructed mini Derenzo phantom, rods as small as 0.35 mm (XUHR-M), 0.50 mm (GP-M) for the two-detector as well as the three-detector SPECT and 0.75 mm (UHS-M) were resolved. Uniformity for maximum resolution recorded 40.7% (XUHR-M), 29.1% (GP-M, U-SPECT5-E), 16.3% (GP-M, U-SPECT+) and 23.0% (UHS-M), respectively. UHS-M reached highest CNR values for low-count images; for rods smaller than 0.45 mm, acceptable CNR was only achieved by XUHR-M. GP-M was superior for imaging rods sized from 0.60-1.50 mm for intermediate activity concentrations. U-SPECT5-E and U-SPECT+ both provided comparable CNR.Conclusions: While uniformity and sensitivity are negatively affected by the absence of a third detector, the investigated U-SPECT5-E system with two stationary detectors delivers excellent spatial resolution and CNR comparable to the performance of an established three-detector-setup.

scholarly journals Performance evaluation of fifth-generation ultra-high-resolution SPECT system with two stationary detectors and multi-pinhole imaging

2020 ◽  
Vol 7 (1) ◽  
Author(s):  
Jan V. Hoffmann ◽  
Jan P. Janssen ◽  
Takayuki Kanno ◽  
Takayuki Shibutani ◽  
Masahisa Onoguchi ◽  
...  
Keyword(s):  
High Resolution ◽  
Spatial Resolution ◽  
Single Photon ◽  
Photon Emission ◽  
Small Animal ◽  
High Sensitivity ◽  
General Purpose ◽  
Emission Computed Tomography ◽  
High Count ◽  
Spect System

Abstract Background Small-animal single-photon emission computed tomography (SPECT) systems with multi-pinhole collimation and large stationary detectors have advantages compared to systems with moving small detectors. These systems benefit from less labour-intensive maintenance and quality control as fewer prone parts are moving, higher accuracy for focused scans and maintaining high resolution with increased sensitivity due to focused pinholes on the field of view. This study aims to investigate the performance of a novel ultra-high-resolution scanner with two-detector configuration (U-SPECT5-E) and to compare its image quality to a conventional micro-SPECT system with three stationary detectors (U-SPECT+). Methods The new U-SPECT5-E with two stationary detectors was used for acquiring data with 99mTc-filled point source, hot-rod and uniformity phantoms to analyse sensitivity, spatial resolution, uniformity and contrast-to-noise ratio (CNR). Three dedicated multi-pinhole mouse collimators with 75 pinholes each and 0.25-, 0.60- and 1.00-mm pinholes for extra ultra-high resolution (XUHR-M), general-purpose (GP-M) and ultra-high sensitivity (UHS-M) imaging were examined. For CNR analysis, four different activity ranges representing low- and high-count settings were investigated for all three collimators. The experiments for the performance assessment were repeated with the same GP-M collimator in the three-detector U-SPECT+ for comparison. Results Peak sensitivity was 237 cps/MBq (XUHR-M), 847 cps/MBq (GP-M), 2054 cps/MBq (UHS-M) for U-SPECT5-E and 1710 cps/MBq (GP-M) for U-SPECT+. In the visually analysed sections of the reconstructed mini Derenzo phantoms, rods as small as 0.35 mm (XUHR-M), 0.50 mm (GP-M) for the two-detector as well as the three-detector SPECT and 0.75 mm (UHS-M) were resolved. Uniformity for maximum resolution recorded 40.7% (XUHR-M), 29.1% (GP-M, U-SPECT5-E), 16.3% (GP-M, U-SPECT+) and 23.0% (UHS-M), respectively. UHS-M reached highest CNR values for low-count images; for rods smaller than 0.45 mm, acceptable CNR was only achieved by XUHR-M. GP-M was superior for imaging rods sized from 0.60 to 1.50 mm for intermediate activity concentrations. U-SPECT5-E and U-SPECT+ both provided comparable CNR. Conclusions While uniformity and sensitivity are negatively affected by the absence of a third detector, the investigated U-SPECT5-E system with two stationary detectors delivers excellent spatial resolution and CNR comparable to the performance of an established three-detector-setup.

scholarly journals Performance Evaluation of Fifth-generation Ultra-high-resolution Spect System With Two Stationary Detectors and Multi-pinhole Imaging

2020 ◽  
Author(s):  
Jan V Hoffmann ◽  
Jan P Janssen ◽  
Takayuki Kanno ◽  
Takayuki Shibutani ◽  
Masahisa Onoguchi ◽  
...  
Keyword(s):  
High Resolution ◽  
Spatial Resolution ◽  
Single Photon ◽  
Photon Emission ◽  
Small Animal ◽  
High Sensitivity ◽  
Emission Computed Tomography ◽  
High Count ◽  
Comparison Results ◽  
Spect System

Abstract Purpose Small-animal single-photon emission computed tomography (SPECT) systems with multi-pinhole collimation and large stationary detectors have advantages compared to systems with moving small detectors. This study aims to investigate the performance of a novel ultra-high-resolution scanner with two-detector-configuration (U-SPECT5-E) and to compare its image quality to a conventional micro-SPECT system with three stationary detectors (U-SPECT+). Methods The new U-SPECT5-E with two stationary detectors was used for acquiring data with 99mTc-filled point source, hot-rod and uniformity phantoms to analyse sensitivity, spatial resolution, uniformity and contrast-to-noise ratio (CNR). Three dedicated multi-pinhole mouse collimators with 75 pinholes each and 0.25-, 0.60- and 1.00-mm pinholes for extra ultra-high resolution (XUHR-M), general-purpose (GP-M) and ultra-high sensitivity (UHS-M) imaging were examined. For CNR analysis, four different activity ranges representing low- and high-count settings were investigated for all three collimators. The experiments for the performance assessment were repeated with the same GP-M collimator in the three-detector U-SPECT+ for comparison. Results Peak sensitivity was 237 cps/MBq (XUHR-M), 847 cps/MBq (GP-M), 2054 cps/MBq (UHS-M) for U-SPECT5-E and 1710 cps/MBq (GP-M) for U-SPECT+. Resolution in the visually analysed sections of the reconstructed hot-rod phantom was 0.35 mm (XUHR-M), 0.50 mm (GP-M) for the two-detector as well as the three-detector SPECT and 0.75 mm (UHS-M). Uniformity for maximum resolution recorded 40.7% (XUHR-M), 29.1% (GP-M, U-SPECT5-E), 16.3% (GP-M, U-SPECT+) and 23.0% (UHS-M), respectively. UHS-M reached highest CNR values for low-count images; for rods smaller than 0.45 mm, acceptable CNR was only achieved by XUHR-M. GP-M was superior for imaging rods sized from 0.60–1.50 mm for intermediate activity concentrations. U-SPECT5-E and U-SPECT+ both provided comparable CNR. Conclusions While uniformity and sensitivity are negatively affected by the absence of a third detector, the investigated U-SPECT5-E system with two stationary detectors delivers excellent spatial resolution and CNR comparable to the performance of an established three-detector-setup.

scholarly journals Development of a High-resolution SSR-SPECT System for Preclinical Imaging and Neuroimaging

2021 ◽  
Author(s):  
Annunziata D'Elia ◽  
Andrea Soluri ◽  
Filippo Galli ◽  
Sara Schiavi ◽  
Giselda De Silva ◽  
...  
Keyword(s):  
Spatial Resolution ◽  
Single Photon ◽  
Photon Emission ◽  
Small Animal Imaging ◽  
Small Animal ◽  
Emission Computed Tomography ◽  
Preclinical Research ◽  
Preclinical Imaging ◽  
Spect System

Abstract The utility of animal models in preclinical research has been increasing by the availability of methods for in vivo imaging. In particular, techniques like single photon emission computed tomography (SPECT) show high potential, which is usually limited by spatial resolution. This represents an important parameter influencing scanner design, given the small size of the anatomical structures to be investigated. The purpose of the present work was to assess the performance of a scintigraphic system with improved spatial resolution based on our previous detector by applying the Super Spatial Resolution (SSR). Our dual-head SPECT system is composed of gamma cameras based on the Hamamatsu H13700 position-sensitive photomultiplier tube (PSPMT). In each detector head, the PSPMT is coupled to a 28×28 array of CRY018 scintillation crystals. The pure Tungsten parallel square hole collimator ensures the position sensitivity, and a dedicated resistive chain readout so as an ADC board have been proprietary designed. To finalize the mechanical development of the SSR-SPECT system several tests were carried out. Based on the results obtained in the test phase, a partial review of the mechanical design was performed. Then a dedicated machine handling software was developed, and in particular, a kinematic software debugging and testing was assessed. Finally, several experiments were carried out by using Derenzo phantoms and capillaries filled with radioactive sources. Finally, the performance of our system was evaluated performing small animal imaging studies. The SPECT spatial resolution was experimentally determined to be about 1.6 mm. We reach a resolution of 1.18 mm by applying the SSR based on two images. The results of this study demonstrated the good capability of the system as a suitable tool for preclinical imaging especially in fields like neuroscience for the study of small brain structures.

Sign in / Sign up

Export Citation Format

Share Document