scholarly journals Finite Element Analysis of the Stress Field in Peri-Implant Bone: A Parametric Study of Influencing Parameters and Their Interactions for Multi-Objective Optimization

2020 ◽  
Vol 10 (17) ◽  
pp. 5973
Author(s):  
Paul Didier ◽  
Boris Piotrowski ◽  
Gael Le Coz ◽  
David Joseph ◽  
Pierre Bravetti ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Young’S Modulus ◽  
Load Transfer ◽  
Young's Modulus ◽  
Element Model ◽  
Implant Design ◽  
Main Effects ◽  
Full Factorial ◽  
Surrounding Bone

The present work proposes a parametric finite element model of the general case of a single loaded dental implant. The objective is to estimate and quantify the main effects of several parameters on stress distribution and load transfer between a loaded dental implant and its surrounding bone. The interactions between them are particularly investigated. Seven parameters (implant design and material) were considered as input variables to build the parametric finite element model: the implant diameter, length, taper and angle of inclination, Young’s modulus, the thickness of the cortical bone and Young’s modulus of the cancellous bone. All parameter combinations were tested with a full factorial design for a total of 512 models. Two biomechanical responses were identified to highlight the main effects of the full factorial design and first-order interaction between parameters: peri-implant bone stress and load transfer between bones and implants. The description of the two responses using the identified coefficients then makes it possible to optimize the implant configuration in a case study with type IV. The influence of the seven considered parameters was quantified, and objective information was given to support surgeon choices for implant design and placement. The implant diameter and Young’s modulus and the cortical thickness were the most influential parameters on the two responses. The importance of a low Young’s modulus alloy was highlighted to reduce the stress shielding between implants and the surrounding bone. This method allows obtaining optimized configurations for several case studies with a custom-made design implant.

Biomechanical Influence of Disk Properties on the Load Transfer of Healthy and Degenerated Disks Using a Poroelastic Finite Element Model

2010 ◽  
Vol 132 (11) ◽  
Author(s):  
Amélie Chagnon ◽  
Carl-Éric Aubin ◽  
Isabelle Villemure
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Young’S Modulus ◽  
Significant Influence ◽  
Load Transfer ◽  
Young's Modulus ◽  
Load Sharing ◽  
Element Model ◽  
Creep Response ◽  
Disk Height

Spine degeneration is a pathology that will affect 80% of the population. Since the intervertebral disks play an important role in transmitting loads through the spine, the aim of this study was to evaluate the biomechanical impact of disk properties on the load carried by healthy (Thompson grade I) and degenerated (Thompson grades III and IV) disks. A three-dimensional parametric poroelastic finite element model of the L4/L5 motion segment was developed. Grade I, grade II, and grade IV disks were modeled by altering the biomechanical properties of both the annulus and nucleus. Models were validated using published creep experiments, in which a constant compressive axial stress of 0.35 MPa was applied for 4 h. Pore pressure (PP) and effective stress (SE) were analyzed as a function of time following loading application (1 min, 5 min, 45 min, 125 min, and 245 min) and discal region along the midsagittal profile for each disk grade. A design of experiments was further implemented to analyze the influence of six disk parameters (disk height (H), fiber proportion (%F), drained Young's modulus (Ea,En), and initial permeability (ka,kn) of both the annulus and nucleus) on load-sharing for disk grades I and IV. Simulations of grade I, grade III, and grade IV disks agreed well with the available published experimental data. Disk height (H) had a significant influence (p<0.05) on the PP and SE during the entire loading history for both healthy and degenerated disk models. Young’s modulus of the annulus (Ea) significantly affected not only SE in the annular region for both disk grades in the initial creep response but also SE in the nucleus zone for degenerated disks with further creep response. The nucleus and annulus permeabilities had a significant influence on the PP distribution for both disk grades, but this effect occurred at earlier stages of loading for degenerated than for healthy disk models. This is the first study that investigates the biomechanical influence of both geometrical and material disk properties on the load transfer of healthy and degenerated disks. Disk height is a significant parameter for both healthy and degenerated disks during the entire loading. Changes in the annulus stiffness, as well as in the annulus and nucleus permeability, control load-sharing in different ways for healthy and degenerated disks.

Prediction of Elastic Constants of Carbon Fabric/Polyurethane Composites

2016 ◽  
Vol 258 ◽  
pp. 233-236 ◽  
Author(s):  
Shun Fa Hwang ◽  
Hsuan Ting Liu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Young’S Modulus ◽  
Elastic Constants ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Element Model ◽  
Curing Temperature ◽  
Poisson's Ratio ◽  
Fiber Fabric

The purpose of this work is to study a new composite material consisting of polyurethane (PU) resin and carbon fiber fabric. This PU resin is superior in impact, viscosity, low curing temperature, and short curing time. If this resin is combined with fiber fabric by vacuum assisted resin transfer method, the fabrication time will be short. Since it is a braided composite, it’s important to have a model to predict the elastic constants for different braid angels. To predict the elastic constants including Young’s modulus, shear modulus, and Poisson’s ratio, a finite element model is established. In this model a braided layer is treated as two uni-directional layers. Then, the elastic constants of this composite with different braid angels are estimated. After that, the composites with different braid angels are fabricated and tested to obtain the elastic constants, and the comparison with the finite element results is made. The results indicate that the agreement is very good for the Young’s modulus. For the Poisson’s ratio, the difference between the prediction and the measurement is reasonable. From the comparison, it can be concluded that the finite element model is good. Then, this model is used to predict all in-plane elastic constants for arbitrary braid angles.

Sign in / Sign up

Export Citation Format

Share Document