Two-Step Identification of Instantaneous Cutting Force Coefficients and Cutter Runout

2014 ◽  
Vol 887-888 ◽  
pp. 1179-1183 ◽  
Author(s):  
Hong Yan Hao ◽  
Wen Cheng Tang ◽  
Bao Sheng Wang
Keyword(s):  
Cutting Force ◽  
End Milling ◽  
Chip Thickness ◽  
Key Factors ◽  
Cutter Runout ◽  
Cutting Force Coefficients ◽  
Force Coefficients ◽  
Instantaneous Cutting Force Coefficients ◽  
Identification Approach ◽  
Milling Forces

Cutting force coefficients and cutter runout parameters are the key factors for accurate prediction of instantaneous milling forces. A new two-step identification method is presented to calibrate them in end milling. Based on analyzing effects of cutter runout on milling forces, a method of extracting nominal milling forces from measured milling forces is proposed. By calibrating average cutting force coefficients and corresponding average chip thickness, an approach to evaluate the instantaneous cutting force coefficients is proposed. Then, an iterative method is presented to identify cutter runout, and the procedure is also given in detail. Milling tests are performed to test the proposed method, and validity of the identification approach is proved by a good agreement between predicted results and experimental results.

Study of Effect of Teeth Number on Cutting Force for Cutter Selection in the End Milling of TC4

2019 ◽  
Author(s):  
Kaining Shi ◽  
Ning Liu ◽  
Sibao Wang ◽  
Chi Ma ◽  
Bo Yang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
End Milling ◽  
Chip Thickness ◽  
Machining Efficiency ◽  
Machining Processes ◽  
Cutting Force Coefficients ◽  
Side Milling ◽  
Force Coefficients ◽  
Comparison Results

Abstract Cutting force is a very important factor in machining processes for predicting chatter, surface roughness and machining efficiency. For a given cutter, cutting force is determined by cutting force coefficients and uncut chip thickness. Once a new cutter is adopted, repeated experiments are carried out to calibrate its cutting force coefficients. To reduce the high cost and longtime experiments, theoretical analysis of the effect of cutter parameters on cutting force is required. In current literatures, some cutter parameters, such as helix angle and pitch angle, have been studied to explore their effects on cutting force. However, there is little research about the effect of teeth number on the cutting force. To fill up this gap, the effect of teeth number on cutting force is studied in the paper. Firstly, it is derived and experimentally verified that the cutting force coefficients are unchanged for cutters with different teeth number but the same teeth parameters, e.g., rake angle, shear angle, etc. Secondly, by matching the measured cutting force point with the cutter rotation angle, the cutting force coefficients can be calibrated by only one experiment when we assume that the material of the cutter is the same. Therefore, the cutting forces generated by cutters with different teeth numbers can be predicted based on only one experiment. Thirdly, from the various comparisons, it is concluded that cutter with 2 teeth number is suggested for side milling and cutter with 3 teeth number is suggested for slotting when surface roughness is considered. The cutter with 5 teeth number is suggested when only the machining efficiency is concerned. Finally, various experiments are carried out to verify the proposed study in milling of titanium alloy Ti6Al4V (TC4), and the comparison results show a good agreement.

3D Ball-End Milling Force Model Using Instantaneous Cutting Force Coefficients

2005 ◽  
Vol 127 (1) ◽  
pp. 1-12 ◽  
Author(s):  
Jeong Hoon Ko ◽  
Dong-Woo Cho
Keyword(s):  
Cutting Force ◽  
End Milling ◽  
Cutting Conditions ◽  
Force Model ◽  
Cutting Force Model ◽  
Cutting Force Coefficients ◽  
Milling Force ◽  
Ball End Milling ◽  
Force Coefficients ◽  
Instantaneous Cutting Force Coefficients

Application of a ball-end milling process model to a CAD/CAM or CAPP system requires a generalized methodology to determine the cutting force coefficients for different cutting conditions. In this paper, we propose a mechanistic cutting force model for 3D ball-end milling using instantaneous cutting force coefficients that are independent of the cutting conditions. The uncut chip thickness model for three-dimensional machining considers cutter deflection and runout. An in-depth analysis of the characteristics of these cutting force coefficients, which can be determined from only a few test cuts, is provided. For more accurate cutting force predictions, the size effect is also modeled using the cutter edge length of the ball-end mill and is incorporated into the cutting force model. This method of estimating the 3D ball-end milling force coefficients has been tested experimentally for various cutting conditions.

A Mechanistic Model of Cutting Forces in Micro-End-Milling With Cutting-Condition-Independent Cutting Force Coefficients

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Han Ul Lee ◽  
Dong-Woo Cho ◽  
Kornel F. Ehmann
Keyword(s):  
Cutting Force ◽  
Cutting Forces ◽  
End Milling ◽  
Cutting Conditions ◽  
Thickness Effect ◽  
Force Model ◽  
Cutting Force Coefficients ◽  
Force Coefficients ◽  
Micro End Milling ◽  
Cutting Mechanisms

Complex three-dimensional miniature components are needed in a wide range of industrial applications from aerospace to biomedicine. Such products can be effectively produced by micro-end-milling processes that are capable of accurately producing high aspect ratio features and parts. This paper presents a mechanistic cutting force model for the precise prediction of the cutting forces in micro-end-milling under various cutting conditions. In order to account for the actual physical phenomena at the edge of the tool, the components of the cutting force vector are determined based on the newly introduced concept of the partial effective rake angle. The proposed model also uses instantaneous cutting force coefficients that are independent of the end-milling cutting conditions. These cutting force coefficients, determined from measured cutting forces, reflect the influence of the majority of cutting mechanisms involved in micro-end-milling including the minimum chip-thickness effect. The comparison of the predicted and measured cutting forces has shown that the proposed method provides very accurate results.

Sign in / Sign up

Export Citation Format

Share Document