2000-2020: Two Decades of Evolution of Hydraulic Fracturing-Induced Seismicity in the Western Canada Sedimentary Basin

The goal of this work is to calibrate a regional predictive model for maximum magnitude of seismic activity associated with hydraulic-fracturing in low-permeability formations in the Western Canada Sedimentary Basin (WCSB). Hydraulic fracturing data (i.e. total injected volume, injection rate, and pressure) were compiled from more than 40,000 hydraulic-fractured wells in the WCSB. These wells were drilled into more than 100 different formations over a 20-year period (January 1st, 2000 and January 1st, 2020). The total injected volume per unit area was calculated utilizing an area of 0.2° in longitude by 0.1° in latitude (or approximately 13x11km, somewhat larger than a standard township of 6x6 miles). This volume was then used to correlate with reported seismicity in the same unit areas. Collectively, within the 143 km2 area considered in this study, a correlation between the total injected volume and the maximum magnitude of seismic events was observed. Results are similar to the maximum-magnitude forecasting model proposed by A. McGarr (JGR, 2014) for seismic events induced by wastewater injection wells in central US. The McGarr method is also based on the total injected fluid per well (or per multiple nearby wells located in the same unit area). However, in some areas in the WCSB, lower injected fluid volumes than the McGarr model predicts were needed to induce seismic events of magnitude 3.0 or higher, although with a similar linear relation. The result of this work is the calculation of a calibration parameter for the McGarr model to better predict the magnitudes of seismic events associated with the injected volumes of hydraulic fracturing. This model can be used to predict induced seismicity in future unconventional hydraulic fracturing treatments and prevent large-magnitude seismic events from occurring. The rich dataset available from the WCSB allowed us to carry out a robust analysis of the influence of critical parameters (such as the total injected fluid) in the maximum magnitude of seismic events associated with the hydraulic-fracturing stimulation of unconventional wells. This analysis could be replicated for any other sedimentary basin with unconventional wells by compiling similar stimulation and earthquake data as in this study.

Significance and Distribution of Apatite in the Triassic Doig Phosphate Zone, Western Canada Sedimentary Basin

The Doig Phosphate Zone (DPZ) is a phosphate-bearing marine unit located at the base of the Doig Formation, in the Triassic section of the Western Canada Sedimentary Basin. The DPZ has a maximum thickness of 90 m and extends across northeastern British Columbia and west-central Alberta. In this study, we characterize the significance and interpret the origin of apatite in the DPZ through mineralogical and geochemical analyses, thin section study, and field emission scanning electron microscopy. The occurrence of apatite in the DPZ is not evenly distributed but restricted to discrete 10 to 20 cm thick beds, located near the base of the DPZ. Phosphorites are of two types: grainstones composed primarily of unconformity-bounded coated grains, and intraclastic phosphorites composed of detrital silt-sized grains and apatite coated grains in a cryptocrystalline phosphatic matrix. The phosphorite beds are records of stratigraphic condensation due to low detrital input during transgression. The erosionally truncated phosphatic coated grains and intraclasts are interpreted to be a result of various phases of phosphatization, exhumation, erosion, reworking, winnowing, and redeposition in alternating quiescence and storms or bottom currents. The abundance of pyrite and chalcophile trace elements, as well as the low concentration of proxy elements for organic matter productivity and preservation, are further evidence of stratigraphic condensation, with sulfidic pore water development and extensive organic recycling promoted by biological activity during the long exposure times. The phosphorites were formed under oxygenated water conditions, as suggested by the depletion in Ce and the presence of a diverse benthic fauna.

Significance and Distribution of Apatite in the Doig Phosphate Zone

The Doig Phosphate Zone (DPZ) is a phosphate-bearing marine unit located at the base of the Doig Formation, in the Triassic section of the Western Canada Sedimentary Basin. The DPZ has a maximum thickness of 90 m and extends across northeastern British Columbia and western central Alberta. In this study we characterize the significance and interpret the origin of apatite in the DPZ, through mineralogical and geochemical analyses, thin section study and field emission-scanning electron microscopy. The occurrence of apatite in the DPZ is not evenly distributed, but restricted to discrete 10 to 20 cm thick beds, located near the base of the DPZ. Phosphorites are of two types: grainstones composed primarily of unconformity-bounded coated grains, and intraclastic phosphorites composed of detrital silt-sized grains and apatite coated grains in a cryptocrystalline phosphatic matrix. The phosphorite beds are records of stratigraphic condensation due to low detrital input during transgression. The erosionally-truncated phosphatic coated grains and intraclasts are interpreted to be a result of various phases of phosphatization, exhumation, erosion reworking, winnowing and redeposition in alternating quiescence and storms or bottom currents. The abundance of pyrite and chalcophile trace elements, as well as the low concentration of proxy elements for organic matter productivity and preservation, are further evidences of stratigraphic condensation, with sulfidic pore water development and extensive organic recycling promoted by biological activity during the long exposure times. The phosphorites were formed under oxygenated water conditions, as suggested by the depletion in Ce and presence of a diverse benthic fauna.