Ultra‐Stretchable, Variable Modulus, Shape Memory Multi‐Purpose Low Hysteresis Hydrogel Derived from Solvent‐Induced Dynamic Micelle Sea‐Island Structure

2021 ◽  
pp. 2011259
Author(s):  
Yanyan Li ◽  
Dingqian Wang ◽  
Jie Wen ◽  
Jinming Liu ◽  
Dongyue Zhang ◽  
...  
Keyword(s):  
Shape Memory ◽  
Island Structure ◽  
Variable Modulus

Tensile Failure of 55-Nitinol Wire

1975 ◽  
Vol 33 ◽  
pp. 46-47
Author(s):  
F. I. Grace
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Stoichiometric Composition ◽  
Tensile Failure ◽  
Initial State ◽  
Initial Shape ◽  
Nitinol Wire ◽  
Cscl Type ◽  
Shear Transformation

An interest in NiTi alloys with near stoichiometric composition (55 NiTi) has intensified since they were found to exhibit a unique mechanical shape memory effect at the Naval Ordnance Laboratory some twelve years ago (thus refered to as NITINOL alloys). Since then, the microstructural mechanisms associated with the shape memory effect have been investigated and several interesting engineering applications have appeared.The shape memory effect implies that the alloy deformed from an initial shape will spontaneously return to that initial state upon heating. This behavior is reported to be related to a diffusionless shear transformation which takes place between similar but slightly different CsCl type structures.

TEM study of order, structure and defects of β and martensite in Cu-Al-Mn shape memory alloys

1990 ◽  
Vol 48 (4) ◽  
pp. 188-189
Author(s):  
J.M. Guilemany ◽  
F. Peregrin
Keyword(s):  
Shape Memory ◽  
Orthophosphoric Acid ◽  
Isopropyl Alcohol ◽  
Metastable Phase ◽  
Characteristic Temperature ◽  
Ethanol Solution ◽  
Order Structure ◽  
Thin Foils ◽  
Polycrystalline Alloys ◽  
Diamond Saw

The shape memory effect (SME) shown by Cu-Al-Mn alloys stems from the thermoelastic martensitic transformation occuring between a β (L2,) metastable phase and a martensitic phase. The TEM study of both phases in single and polycrystalline Cu-Al-Mn alloys give us greater knowledge of the structure, order and defects.The alloys were obtained by vacuum melting of Cu, Al and Mn and single crystals were obtained from polycrystalline alloys using a modified Bridgman method. Four different alloys were used with (e/a) ranging from 1.41 to 1.46 . Two different heat treatments were used and the alloys also underwent thermal cycling throughout their characteristic temperature range -Ms, Mf, As, Af-. The specimens were cut using a low speed diamond saw and discs were mechanically thinned to 100 μm and then ion milled to perforation at 4 kV. Some thin foils were also prepared by twin-jet electropolishing, using a (1:10:50:50) urea: isopropyl alcohol: orthophosphoric acid: ethanol solution at 20°C. The foils were examinated on a TEM operated at 200 kV.

Atomic Order and Martensitic Transformation in Cu-Al-Be Shape Memory Alloys

1995 ◽  
Vol 05 (C8) ◽  
pp. C8-973-C8-978
Author(s):  
M. Jurado ◽  
Ll. Mañosa ◽  
A. González-Comas ◽  
C. Stassis ◽  
A. Planes
Keyword(s):  
Martensitic Transformation ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Atomic Order

Cu-AI based single crystal shape memory actuators and drives

2003 ◽  
Vol 112 ◽  
pp. 1181-1184 ◽  
Author(s):  
I. Vahhi ◽  
S. Pulnev ◽  
A. Priadko
Keyword(s):  
Single Crystal ◽  
Shape Memory ◽  
Crystal Shape ◽  
Shape Memory Actuators
Sign in / Sign up

Export Citation Format

Share Document