A Decomposition Approach for Optimal Processing of Telecommunications and Cyberspace Systems

2003 ◽  
pp. 293-308
Author(s):  
Victor Korotkikh ◽  
Noel Patson
Keyword(s):  
Decomposition Approach ◽  
Optimal Processing

Parametrical Synthesis of Linear Controllers in Aperiodical Systems on Basis of Decomposition Approach

2019 ◽  
Vol 12 (4) ◽  
pp. 192
Author(s):  
Sergey Anatolevich Gayvoronskiy ◽  
Tatiana Ezangina ◽  
Maxim Pushkarev ◽  
Ivan Khozhaev
Keyword(s):  
Decomposition Approach ◽  
Linear Controllers

Optimal Processing of Information from Inertial and Satellite Navigation Systems by Analysis after Flight

2001 ◽  
Vol 56 (3) ◽  
pp. 13
Author(s):  
E. G. Kharin ◽  
V. G. Maslennikov ◽  
N. B. Vavilova ◽  
I. A. Kopylov ◽  
A. Ch. Staroverov
Keyword(s):  
Satellite Navigation ◽  
Navigation Systems ◽  
Optimal Processing ◽  
Satellite Navigation Systems

scholarly journals Warpage Optimisation Using Recycled Polycar-bonates (PC) on Front Panel Housing

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1416
Author(s):  
Nur Aisyah Miza Ahmad Tamizi ◽  
Shayfull Zamree Abd Rahim ◽  
Abdellah El-hadj Abdellah ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Marcin Nabiałek ◽  
...  
Keyword(s):  
Simulation Analysis ◽  
Processing Parameters ◽  
Front Panel ◽  
Processing Parameter ◽  
Mechanical Recycling ◽  
Great Opportunity ◽  
Average Value ◽  
Optimal Processing ◽  
Materials Used ◽  
Optimisation Methods

Many studies have been done using recycled waste materials to minimise environmental problems. It is a great opportunity to explore mechanical recycling and the use of recycled and virgin blend as a material to produce new products with minimum defects. In this study, appropriate processing parameters were considered to mould the front panel housing part using R0% (virgin), R30% (30% virgin: 70% recycled), R40% (40% virgin: 60% recycled) and R50% (50% virgin: 50% recycled) of Polycarbonate (PC). The manufacturing ability and quality during preliminary stage can be predicted through simulation analysis using Autodesk Moldflow Insight 2012 software. The recommended processing parameters and values of warpage in x and y directions can also be obtained using this software. No value of warpage was obtained from simulation studies for x direction on the front panel housing. Therefore, this study only focused on reducing the warpage in the y direction. Response Surface Methodology (RSM) and Genetic Algorithm (GA) optimisation methods were used to find the optimal processing parameters. As the results, the optimal ratio of recycled PC material was found to be R30%, followed by R40% and R50% materials using RSM and GA methods as compared to the average value of warpage on the moulded part using R0%. The most influential processing parameter that contributed to warpage defect was packing pressure for all materials used in this study.

An improved decomposition approach toward energy rebound effects in China: Review since 1992

2021 ◽  
Vol 145 ◽  
pp. 111141
Author(s):  
Jiandong Chen ◽  
Ming Gao ◽  
Muhammad Shahbaz ◽  
Shulei Cheng ◽  
Malin Song
Keyword(s):  
Decomposition Approach ◽  
Rebound Effects
Sign in / Sign up

Export Citation Format

Share Document