Calculation of Circulating Current Inside Power Transformers in Non-symmetrical Configurations

2019 ◽  
pp. 67-74
Author(s):  
Bruno Jurišić ◽  
Tomislav Župan ◽  
Leonardo Štrac
Keyword(s):  
Power Transformers ◽  
Circulating Current

A Study of Circulating Current in Parallel-Connected Armature Windings of Synchronous Machines

2013 ◽  
Vol 133 (1) ◽  
pp. 50-55
Author(s):  
Akihito Nakahara ◽  
Jun Yoshida ◽  
Masayuki Okada
Keyword(s):  
Synchronous Machines ◽  
Circulating Current

Data Driven Analytical Modeling of Power Transformers

2017 ◽  
Vol 10 (2) ◽  
pp. 85
Author(s):  
Jyrki Sakari Penttonen ◽  
Matti Lehtonen
Keyword(s):  
Analytical Modeling ◽  
Data Driven ◽  
Power Transformers

A strategy to locate partial discharges in power transformers using acoustic emission

2007 ◽  
Vol 1 (05) ◽  
pp. 596-600 ◽  
Author(s):  
Giscard Franceire Cintra Veloso ◽  
◽  
Luiz Eduardo Borges da Silva ◽  
Germano Lambert-Torres
Keyword(s):  
Acoustic Emission ◽  
Partial Discharges ◽  
Power Transformers

A Solid-State On-Load Tap Changer for the Power Transformers of 10—0.4 kV Distribution Networks

Vestnik MEI ◽  
2020 ◽  
Vol 6 (6) ◽  
pp. 82-90
Author(s):  
Dmitriy I. Panfilov ◽  
◽  
Mikhail G. Astashev ◽  
Aleksandr V. Gorchakov ◽  
◽  
...  
Keyword(s):  
Solid State ◽  
Physical Model ◽  
High Speed ◽  
Power Transformer ◽  
Voltage Control ◽  
Power Transformers ◽  
Control Algorithms ◽  
Load Voltage ◽  
Tap Changer ◽  
Load Tap Changer

The specific features relating to voltage control of power transformers at distribution network transformer substations are considered. An approach to implementing high-speed on-load voltage control of serially produced 10/0.4 kV power transformers by using a solid-state on-load tap changer (SOLTC) is presented. An example of the SOLTC circuit solution on the basis of thyristor switches is given. On-load voltage control algorithms for power transformers equipped with SOLTC that ensure high reliability and high-speed operation are proposed. The SOLTC performance and the operability of the suggested voltage control algorithms were studied by simulation in the Matlab/Simulink environment and by experiments on the SOLTC physical model. The structure and peculiarities of the used simulation Matlab model are described. The SOLTC physical model design and its parameters are presented. The results obtained from the simulating the SOLTC operation on the Matlab model and from the experiments on the SOLTS physical model jointly with a power transformer under different loads and with using different control algorithms are given. An analysis of the experimental study results has shown the soundness of the adopted technical solutions. It has been demonstrated that the use of an SOLTC ensures high-speed voltage control, high efficiency and reliability of its operation, and arcless switching of the power transformer regulating taps without load voltage and current interruption. By using the SOLTC operation algorithms it is possible to perform individual phase voltage regulation in a three-phase 0.4 kV distribution network. The possibility of integrating SOLTC control and diagnostic facilities into the structure of modern digital substations based on the digital interface according to the IEC 61850 standard is noted.

PROTECTION OF OIL POWER TRANSFORMERS BY MEANS OF WATER BASED SUPPRESSION SYSTEMS

2018 ◽  
pp. 37-42
Author(s):  
Aleksei Rozhkov ◽  
◽  
Darya Perednya ◽  
Vladimir Roitman ◽  
◽  
...  
Keyword(s):  
Power Transformers ◽  
Water Based ◽  
Suppression Systems
Sign in / Sign up

Export Citation Format

Share Document