Experimental Verification of a Non Intrusive Method for Detecting Steam Turbine Blade Resonances

1994 ◽  
pp. 137-147
Author(s):  
C. Cavagnino ◽  
G. L. Lapini ◽  
M. Zippo ◽  
P. Moretti ◽  
R. Bernante
Keyword(s):  
Steam Turbine ◽  
Turbine Blade ◽  
Experimental Verification ◽  
Steam Turbine Blade

scholarly journals Effect of NbC precipitation on toughness of X12CrMoWNbVN10-1-1 martensitic heat resistant steel for steam turbine blade

2021 ◽  
Vol 11 ◽  
pp. 2092-2105
Author(s):  
Xiaogang Li ◽  
Zhipeng Cai ◽  
Mengjia Hu ◽  
Kejian Li ◽  
Mingdong Hou ◽  
...  
Keyword(s):  
Steam Turbine ◽  
Turbine Blade ◽  
Resistant Steel ◽  
Heat Resistant Steel ◽  
Heat Resistant ◽  
Steam Turbine Blade

scholarly journals Failure Analysis in Lacing Wire Of Last Stage Low Pressure Steam Turbine Blade

2021 ◽  
Vol 1096 (1) ◽  
pp. 012097
Author(s):  
A M Kongkong ◽  
H Setiawan ◽  
J Miftahul ◽  
A R Laksana ◽  
I Djunaedi ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Steam Turbine ◽  
Turbine Blade ◽  
Low Pressure ◽  
Pressure Steam ◽  
Steam Turbine Blade ◽  
Last Stage

Studies on Determination of Natural Frequencies of Industrial Turbine Blades

1995 ◽  
Author(s):  
Mahesh M. Bhat ◽  
V. Ramamurti ◽  
C. Sujatha
Keyword(s):  
Steam Turbine ◽  
Dynamic Behavior ◽  
Turbine Blade ◽  
Natural Frequencies ◽  
Complex Structure ◽  
Turbine Blades ◽  
Blade Root ◽  
Steam Turbine Blade ◽  
Manufacturing Tolerances

Abstract Steam turbine blade is a very complex structure. It has geometric complexities like variation of twist, taper, width and thickness along its length. Most of the time these variations are not uniform. Apart from these geometric complexities, the blades are coupled by means of lacing wire, lacing rod or shroud. Blades are attached to a flexible disc which contributes to the dynamic behavior of the blade. Root fixity also plays an important role in this behavior. There is a considerable variation in the frequencies of blades of newly assembled turbine and frequencies after some hours of running. Again because of manufacturing tolerances there can be some variation in the blade to blade frequencies. Determination of natural frequencies of the blade is therefore a very critical job. Problems associated with typical industrial turbine bladed discs of a 235 MW steam turbine are highlighted in this paper.

Failure analysis of the 350MW steam turbine blade root

2009 ◽  
Vol 16 (4) ◽  
pp. 1270-1281 ◽  
Author(s):  
J. Kubiak Sz ◽  
J.A. Segura ◽  
G. Gonzalez R ◽  
J.C. García ◽  
F. Sierra E ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Steam Turbine ◽  
Turbine Blade ◽  
Blade Root ◽  
Steam Turbine Blade

Path Planning for Circular Cutter Envelop Milling of Steam Turbine Blade

2014 ◽  
Vol 989-994 ◽  
pp. 2908-2912
Author(s):  
Jian Jun Wang ◽  
Ke Wang ◽  
Qiong Wu
Keyword(s):  
Steam Turbine ◽  
Turbine Blade ◽  
Tool Path ◽  
Vertical Section ◽  
Surface Matching ◽  
Nurbs Surface ◽  
Processing Efficiency ◽  
Tool Paths ◽  
Blade Machining ◽  
Steam Turbine Blade

In order to solve the problem of poor steam turbine blade processing efficiency, and on the basis of analyzing the turbine blade surface and the existing processing methods, a model of circular cutter turbine blade machining is built. By comparing the tool paths of horizontal and vertical section envelope machining, choosing quasi-vertical cross section envelope machining method and utilizing the original datum and NURBS surface matching mathematic methods, this paper provides an algorithm of residual height calculating, and based on this, the tool path can be planned. Datum show that, the tool path of circular cutter machining blades is much longer than the tool path of ball-end cutter envelop milling machining blades, and the machining efficiency is also highly enhanced.

Sign in / Sign up

Export Citation Format

Share Document