Inhibitory Dimensional Control: The Effects of Discriminative Autoshaping and Negative Automaintenance Procedures

1981 ◽  
Vol 31 (2) ◽  
pp. 221-235 ◽  
Author(s):  
Peter E. Jenkins
Keyword(s):  
Dimensional Control ◽  
Negative Automaintenance

Transmission Electron Microscopy of an Aluminum-Silver-Stainless Steel Solid State Bond

1985 ◽  
Vol 43 ◽  
pp. 172-173
Author(s):  
M. J. Carr ◽  
J. F. Shewbridge ◽  
T. O. Wilford
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Solid State ◽  
Specimen Preparation ◽  
Dimensional Control ◽  
Tem Analysis ◽  
Metal Parts ◽  
Dissimilar Metal ◽  
Transmission Electron ◽  
Short Time

Strong solid state bonds are routinely produced between physical vapor deposited (PVD) silver coatings deposited on sputter cleaned surfaces of two dissimilar metal parts. The low temperature (200°C) and short time (10 min) used in the bonding cycle are advantageous from the standpoint of productivity and dimensional control. These conditions unfortunately produce no microstructural changes at or near the interface that are detectable by optical, SEM, or microprobe examination. Microstructural problems arising at these interfaces could therefore easily go undetected by these techniques. TEM analysis has not been previously applied to this problem because of the difficulty in specimen preparation. The purpose of this paper is to describe our technique for preparing specimens from solid state bonds and to present our initial observations of the microstructural details of such bonds.

Measurement Design for Dimensional Control of Functional Micro-Scale Features on Microfluidic Moulds

2017 ◽  
Author(s):  
Crhistian Baldo ◽  
Luciana Wasnievski da Silva de Luca Ramos ◽  
Jan Mewis
Keyword(s):  
Dimensional Control ◽  
Micro Scale ◽  
Measurement Design

Calculation of the accuracy of a control head of a simplified design for dimensional control of parts

2020 ◽  
pp. 35-37
Author(s):  
Ya.L. Liberman ◽  
A.N. Mahiyanova ◽  
Gorbunova L.N.
Keyword(s):  
Size Control ◽  
Dimensional Control ◽  
Kinematic Accuracy ◽  
Measuring Probe

The metrological scheme of the control head of a simplified design is presented, its kinematic accuracy is analyzed. It is shown, that the effectiveness of the use of the head of this design, i.e., the accuracy of control, when controlling tolerances, in the manufacture of the part depends on the choice of the length of the measuring probe. Keywords part, size, control, measuring probe, kinematic accuracy, metrological scheme. [email protected]

Flatness and dimensional control of planar objects with a novel modular moiré system

1998 ◽  
Vol 29 (3) ◽  
pp. 174-178 ◽  
Author(s):  
Jussi Paakkari ◽  
Heikki Ailisto ◽  
Harri Kopola
Keyword(s):  
Dimensional Control

Achieving Green and Deep-Blue Perovskite LEDs by Dimensional Control Using Various Ammonium Bromides with CsPbBr-3

2021 ◽  
pp. 100749
Author(s):  
Seokwoo Kang ◽  
Sunwoo Park ◽  
Sangshin Park ◽  
Hyukmin Kwon ◽  
Jaehyun Lee ◽  
...  
Keyword(s):  
Dimensional Control ◽  
Deep Blue

Achieving Dimensional Control with Molded Lip Seals

1976 ◽  
Vol 19 (3) ◽  
pp. 181-186 ◽  
Author(s):  
L. A. Horve
Keyword(s):  
Dimensional Control ◽  
Lip Seals

Tuning of photonic bandgap via dimensional control of nano-pillars

2011 ◽  
Vol 8 (7-8) ◽  
pp. 2351-2353 ◽  
Author(s):  
K. H. Li ◽  
H. W. Choi
Keyword(s):  
Photonic Bandgap ◽  
Dimensional Control
Sign in / Sign up

Export Citation Format

Share Document