Real-time localization of micro-damage in concrete beams using DIC technology and wavelet packet analysis

Author(s):  
Kaiyang Zhou ◽  
Dong Lei ◽  
Jintao He ◽  
Pei Zhang ◽  
Pengxiang Bai ◽  
...  
IEEE Access ◽  
2018 ◽  
Vol 6 ◽  
pp. 5208-5214 ◽  
Author(s):  
Wenwei Yang ◽  
Qingzhao Kong ◽  
Siu Chun Michael Ho ◽  
Yi-Lung Mo ◽  
Gangbing Song

2013 ◽  
Vol 437 ◽  
pp. 373-376
Author(s):  
Ye Zhou ◽  
Luo Ping Pan ◽  
Ping Ping Li

Shaft fault is the most common fault for hydraulic machinery. In this paper, wavelet packet energy spectrum analysis method was used for multi frequency bands division of shaft monitoring signals. The variable bands frequency energy can construct feature vectors needed for fault diagnosis based on support vector machine, by integrating the procedure of wavelet packet analysis method and online monitoring technology, feature can be extracted in real time, and it make possible for real-time fault diagnosis and prediction of hydraulic machine.


2018 ◽  
Vol 51 (5-6) ◽  
pp. 138-149 ◽  
Author(s):  
Hüseyin Göksu

Estimation of vehicle speed by analysis of drive-by noise is a known technique. The methods used in this kind of practice generally estimate the velocity of the vehicle with respect to the microphone(s), so they rely on the relative motion of the vehicle to the microphone(s). There are also other methods that do not rely on this technique. For example, recent research has shown that there is a statistical correlation between vehicle speed and drive-by noise emissions spectra. This does not rely on the relative motion of the vehicle with respect to the microphone(s) so it inspires us to consider the possibility of predicting velocity of the vehicle using an on-board microphone. This has the potential for the development of a new kind of speed sensor. For this purpose we record sound signal from a vehicle under speed variation using an on-board microphone. Sound emissions from a vehicle are very complex, which is from the engine, the exhaust, the air conditioner, other mechanical parts, tires, and air resistance. These emissions carry both stationary and non-stationary information. We propose to make the analysis by wavelet packet analysis, rather than traditional time or frequency domain methods. Wavelet packet analysis, by providing arbitrary time-frequency resolution, enables analyzing signals of stationary and non-stationary nature. It has better time representation than Fourier analysis and better high-frequency resolution than Wavelet analysis. Subsignals from the wavelet packet analysis are analyzed further by Norm Entropy, Log Energy Entropy, and Energy. These features are evaluated by feeding them into a multilayer perceptron. Norm entropy achieves the best prediction with 97.89% average accuracy with 1.11 km/h mean absolute error which corresponds to 2.11% relative error. Time sensitivity is ±0.453 s and is open to improvement by varying the window width. The results indicate that, with further tests at other speed ranges, with other vehicles and under dynamic conditions, this method can be extended to the design of a new kind of vehicle speed sensor.


2006 ◽  
Vol 324-325 ◽  
pp. 205-208
Author(s):  
Qing Guo Fei ◽  
Ai Qun Li ◽  
Chang Qing Miao ◽  
Zhi Jun Li

This paper describes a study on damage identification using wavelet packet analysis and neural networks. The identification procedure could be divided into three steps. First, structure responses are decomposed into wavelet packet components. Then, the component energies are used to define damage feature and to train neural network models. Finally, in combination with the feature of the damaged structure response, the trained models are employed to determine the occurrence, the location and the qualification of the damage. The emphasis of this study is put on multi-damage case. Relevant issues are studied in detail especially the selection of training samples for multi-damage identification oriented neural network training. A frame model is utilized in the simulation cases to study the sampling techniques and the multi-damage identification. Uniform design is determined to be the most suitable sampling technique through simulation results. Identifications of multi-damage cases of the frame including different levels of damage at various locations are investigated. The results show that damages are successfully identified in all cases.


Sign in / Sign up

Export Citation Format

Share Document