Vegetation and soil restoration in refuse dumps from open pit coal mines

2016 ◽  
Vol 94 ◽  
pp. 638-646 ◽  
Author(s):  
Huang Lei ◽  
Zhang Peng ◽  
Hu Yigang ◽  
Zhao Yang
Author(s):  
Xinhui Li ◽  
Shaogang Lei ◽  
Feng Liu ◽  
Weizhong Wang

Vegetation and soil restoration are the key to ecological reconstruction in the damaged areas of open-pit coal mining areas. Ecological stability is an important indicator of the degree of ecological restoration. In this study, the ecological stability and the process of plant and soil restoration were investigated at different refuse dumps in three coal mines, namely, the Wulanhada (WLHD) coal mine, the Liulingou (LLG) coal mine, and the Jinzhengtai (JZT) coal mine, in Jungar Banner. Results show that organic matter, total N, available N, and available K increased with the increase in restoration age at the two coal mines of WLHD and LLG. In the JZT coal mine, organic matter, total N, and available K firstly increased, and then slightly decreased with the increase in restoration age. The redundancy analysis indicates that most reclaimed mine soil properties (including soil moisture content, organic matter, total N, and available K) are positively correlated with plant species diversity in the three coal mines, while soil pH and soil bulk density showed a negative correlation with plant species diversity. Plant parameters increased with the years since revegetation, except the Pielou index for the WLHD coal mine, and the Pielou and Margalef indexes for the JZT coal mine. The Euclidean distance between the restoration areas and the natural reference areas decreased with the increase in restoration age. Our findings suggest that, in the three coal mines, the change law of ecological stability conformed to the logistic succession model. The same degree of ecological stability in different refuse dumps may correspond to different degrees of vegetation and soil development. This study emphasizes that ecological restoration in mining areas could benefit the structure of the plant community and the recovery of soil properties, which would eventually improve the ecological stability of coal mining areas.


2017 ◽  
Vol 12 ◽  
pp. 96-108
Author(s):  
E.L. Karibzhanova ◽  
◽  
A.E. Safronov ◽  
O.O. Skryabin ◽  
V.V. Semenyaka ◽  
...  

2017 ◽  
Vol 12 (2) ◽  
pp. 113-122 ◽  
Author(s):  
Mark KORYAGIN ◽  
Artyom VORONOV
Keyword(s):  

2020 ◽  
Vol 1 (2) ◽  
Author(s):  
Le VAN CANH ◽  
Cao XUAN CUONG ◽  
Nguyen QUOC LONG ◽  
Le THI THU HA ◽  
Tran TRUNG ANH ◽  
...  

Open-pit coal mines’ terrain is often complex and quickly and frequently changes. Therefore, topographic surveys of open-pit mines are undertaken on a daily basis. While these tasks are very time-consuming and costly with traditional methods such as total station and GNSS, the unmanned aerial vehicle (UAV) based method can be more efficient. This method is a combination of the “Structure from motion” (SfM) photogrammetry technique and UAV photogrammetry which has been widely used in topographic surveying. With an increasing popularity of RTK-enabled drones, it is becoming even more powerful method. While the important role of ground control points (GCP) in the accuracy of digital surface model (DSM) generated from images acquired by “traditional” UAVs (not RTK-enabled drones) has been proved in many previous studies, it is not clear in the case of RTK-enabled drones, especially for complex terrain in open-pit coal mines. In this study, we experimentally investigated the influence of GCP regarding its numbers and distribution on the accuracy of DSM generation from images acquired by RTK-enabled drones in open-pit coal mines. In addition, the Post Processing Kinematic (PPK) mode was executed over a test field with the same flight altitude. DSM generation was performed with several block control configurations: PPK only, PPK with one GCP, and PPK with two GCPs. Several positions of GCPs were also examined to test the optimal locations for placing GCPs to achieve accurate DSMs. The results show that the horizontal and vertical accuracy given by PPK only were 9.3 and 84.4 cm, respectively. However, when adding at least one GCP, the accuracy was significantly improved in both horizontal and vertical components, with RMSE for XY and Z ranging between 3.8 and 9.8 cm (with one GCP) and between 3.0 and 5.7 cm (with two GCPs), respectively. Also, the GCPs placed in the deep areas of the open-pit mine could ensure the cm-level accuracy.


Author(s):  
Zoran Marković ◽  
Miloš Milivojević ◽  
Bruijn De ◽  
Wilma Wessels ◽  
De Van ◽  
...  

2015 ◽  
pp. 62-65
Author(s):  
A. V. Sokolovsky ◽  
◽  
O. I. Cherskikh ◽  
A. I. Kainov ◽  
◽  
...  
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document