Bioburden assessment and gamma radiation inactivation patterns in parchment documents

2013 ◽  
Vol 88 ◽  
pp. 82-89 ◽  
Author(s):  
Inês Nunes ◽  
Nuno Mesquita ◽  
Sandra Cabo Verde ◽  
Maria Manuela Carolino ◽  
António Portugal ◽  
...  
1973 ◽  
Vol 26 (1) ◽  
pp. 14-17 ◽  
Author(s):  
Robert Sullivan ◽  
Pasquale V. Scarpino ◽  
Alexander C. Fassolitis ◽  
Edward P. Larkin ◽  
James T. Peeler

2017 ◽  
Vol 58 (1) ◽  
pp. 76-80 ◽  
Author(s):  
Mesut Ortatatli ◽  
Kadir Canitez ◽  
Sermet Sezigen ◽  
Ruşen Koray Eyison ◽  
Levent Kenar

1990 ◽  
Vol 53 (4) ◽  
pp. 302-305 ◽  
Author(s):  
C. N. HUHTANEN

Radiation survival curves were determined for 7 strains of Enterococcus faecium, 10 strains of E. faecalis, and 8 strains of the proteolytic variety of E. faecalis. The D values (i.e. the doses giving 90% reduction of viable counts) ranged from 5.0–47 kGy for the E. faecium strains, 3.5–21 kGy for the E. faecalis strains, and 3.0–4.5 kGy for the proteolytic variants of E. faecalis. The survival curves were linear for most strains but some exhibited significant non-linear trends.


1973 ◽  
Vol 26 (1) ◽  
pp. 14-17 ◽  
Author(s):  
Robert Sullivan ◽  
Pasquale V. Scarpino ◽  
Alexander C. Fassolitis ◽  
Edward P. Larkin ◽  
James T. Peeler

Author(s):  
K. Cowden ◽  
B. Giammara ◽  
T. Devine ◽  
J. Hanker

Plaster of Paris (calcium sulfate hemihydrate, CaSO4. ½ H2O) has been used as a biomedical implant material since 1892. One of the primary limiting factors of these implants is their mechanical properties. These materials have low compressive and tensile strengths when compared to normal bone. These are important limiting factors where large biomechanical forces exist. Previous work has suggested that sterilization techniques could affect the implant’s strength. A study of plaster of Paris implant mechanical and physical properties to find optimum sterilization techniques therefore, could lead to a significant increase in their application and promise for future use as hard tissue prosthetic materials.USG Medical Grade Calcium Sulfate Hemihydrate Types A, A-1 and B, were sterilized by dry heat and by gamma radiation. Types A and B were additionally sterilized with and without the setting agent potassium sulfate (K2SO4). The plaster mixtures were then moistened with a minimum amount of water and formed into disks (.339 in. diameter x .053 in. deep) in polyethylene molds with a microspatula. After drying, the disks were fractured with a Stokes Hardness Tester. The compressive strengths of the disks were obtained directly from the hardness tester. Values for the maximum tensile strengths σo were then calculated: where (P = applied compression, D = disk diameter, and t = disk thickness). Plaster disks (types A and B) that contained no setting agent showed a significant loss in strength with either dry heat or gamma radiation sterilization. Those that contained potassium sulfate (K2SO4) did not show a significant loss in strength with either sterilization technique. In all comparisons (with and without K2SO4 and with either dry heat or gamma radiation sterilization) the type B plaster had higher compressive and tensile strengths than that of the type A plaster. The type A-1 plaster however, which is specially modified for accelerated setting, was comparable to that of type B with K2SO4 in both compressive and tensile strength (Table 1).


Sign in / Sign up

Export Citation Format

Share Document