Comments on “Formation of M23C6-type precipitates and chromium-depleted zones in austenite stainless steel, Scr. Mater. 65 (2011) 509–512″

2022 ◽  
Vol 209 ◽  
pp. 114412
Author(s):  
Won Seok Choi ◽  
Hyunjoon Park
Keyword(s):  
Stainless Steel ◽  
Austenite Stainless Steel ◽  
M23c6 Type

Formation of M23C6-type precipitates and chromium-depleted zones in austenite stainless steel

2011 ◽  
Vol 65 (6) ◽  
pp. 509-512 ◽  
Author(s):  
Kenji Kaneko ◽  
Tatsuya Fukunaga ◽  
Kazuhiro Yamada ◽  
Nobuo Nakada ◽  
Masao Kikuchi ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenite Stainless Steel ◽  
M23c6 Type

Effect of milling on the microstructure and mechanical property of austenite stainless steel

2020 ◽  
Vol 62 (12) ◽  
pp. 1181-1186
Author(s):  
Huanchun Wu ◽  
Wenxin Ti ◽  
Guodong Zhang ◽  
Fei Xue ◽  
Chengtao Li ◽  
...  
Keyword(s):  
Mechanical Property ◽  
Stainless Steel ◽  
Austenite Stainless Steel ◽  
Microstructure And Mechanical Property

Recrystallization Mechanisms in Severely Deformed Dual-Phase Stainless Steel

2010 ◽  
Vol 638-642 ◽  
pp. 1905-1910 ◽  
Author(s):  
Andrey Belyakov ◽  
Rustam Kaibyshev ◽  
Yuuji Kimura ◽  
Kaneaki Tsuzaki
Keyword(s):  
Stainless Steel ◽  
Large Strain ◽  
Austenite Phase ◽  
The Other ◽  
Dual Phase ◽  
Austenite Stainless Steel ◽  
Ultrafine Grained ◽  
Continuous Recrystallization ◽  
Ultrafine Grained Microstructure ◽  
Structural Recrystallization

The structural recrystallization mechanisms operating in an Fe – 27%Cr – 9% Ni dual-phase (ferrite-austenite) stainless steel after large strain processing to total strain of 4.4 were investigated in the temperature range of 400-700oC. The severe deformation resulted in the development of an ultrafine grained microstructure consisting of highly elongated grains/subgrains with transverse dimensions of 160 nm and 130 nm in ferrite and austenite, respectively. The annealing mechanism operating in ferrite phase was considered as continuous recrystallization, which involved recovery leading to the development of essentially polygonized microstructure. On the other hand, the mechanism of discontinuous nucleation took place at an early recrystallization stage in austenite phase.

The effect of alternate supply of shielding gases in austenite stainless steel GTA welding

2009 ◽  
Vol 209 (10) ◽  
pp. 4722-4727 ◽  
Author(s):  
B.Y. Kang ◽  
Yarlagadda K.D.V. Prasad ◽  
M.J. Kang ◽  
H.J. Kim ◽  
I.S. Kim
Keyword(s):  
Stainless Steel ◽  
Gta Welding ◽  
Shielding Gases ◽  
Austenite Stainless Steel

scholarly journals Surface Layer Characteristics of S30432 Austenite Stainless Steel after Shot Peening

2012 ◽  
Vol 53 (5) ◽  
pp. 1002-1006 ◽  
Author(s):  
K. Zhan ◽  
C. H. Jiang ◽  
X. Y. Wu ◽  
Vincent Ji
Keyword(s):  
Stainless Steel ◽  
Surface Layer ◽  
Shot Peening ◽  
Austenite Stainless Steel

Improvement of the fatigue strength of SUS304 austenite stainless steel using ultrasonic nanocrystal surface modification

2013 ◽  
Vol 218 ◽  
pp. 93-98 ◽  
Author(s):  
Manabu Yasuoka ◽  
Pangpang Wang ◽  
Kaiyue Zhang ◽  
Zhiyong Qiu ◽  
Kazuya Kusaka ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Surface Modification ◽  
Fatigue Strength ◽  
Austenite Stainless Steel

Study on the Brush Plating Tecnology of Austenite Stainless Steel Parts

2011 ◽  
Vol 239-242 ◽  
pp. 1682-1685
Author(s):  
Bi Xin Guo ◽  
Xiang Yan Luo ◽  
Yun Kui Gao
Keyword(s):  
Stainless Steel ◽  
Austenite Stainless Steel ◽  
Brush Plating

Brush plating has been an important technology for the mending of the scratched surface of the engineering parts in recent years.The process for brush plating mending of scratched surface of the Austenite stainless steel parts is introduced in this article.The merits of the technology are discussed.

Sign in / Sign up

Export Citation Format

Share Document