A hybrid PV/T solar evaporator using CO2: Numerical heat transfer model and simulation results

Solar Energy ◽  
2018 ◽  
Vol 170 ◽  
pp. 1118-1129 ◽  
Author(s):  
Pierre-Luc Paradis ◽  
Daniel R. Rousse ◽  
Louis Lamarche ◽  
Hakim Nesreddine
2021 ◽  
Author(s):  
Vassilis Z. Antonopoulos ◽  
Soultana K. Gianniou

Abstract The knowledge of micrometeorological conditions on water surface of impoundments is crucial for the better modeling of the temperature and water quality parameters distribution in the water body and against the climatic changes. Water temperature distribution is an important factor that affects most physical, chemical and biological processes and reactions occurring in lakes. In this work, different processes of water surface temperature of lake’s estimation based on the energy balance method are considered. The daily meteorological data and the simulation results of energy balance components from an integrated heat transfer model for two complete years as well as the lake’s characteristics for Vegoritis lake in northern Greece were used is this analysis.The simulation results of energy balance components from a heat transfer model are considered as the reference and more accurate procedure to estimate water surface temperature. These results are used to compare the other processes. The examined processes include a) models of heat storage changes in relationship to net radiation (Qt(Rn) values, b) net radiation estimation with different approaches, as the process of Slob’s equation with adjusted coefficients to lake data, and c) ANNs models with different architecture and input variables. The results show that the model of heat balance describes the water surface temperature with high accuracy (r2=0.916, RMSE=2.422oC). The ANN(5,6,1) model in which Tsw(i-1) is incorporated in the input variables was considered the better of all other ANN structures (r2=0.995, RMSE=0.490oC). The use of different approaches for simulating net radiation (Rn) and Qt(Rn) in the equation of water surface temperature gives results with lower accuracy.


2011 ◽  
Vol 99-100 ◽  
pp. 112-115
Author(s):  
Ming Zhi Yu ◽  
Lei Zhang ◽  
Xiao Fei Yu ◽  
Zhao Hong Fang

A two dimensional numerical heat transfer model of buried geothermal heat exchanger has been established by finite element method. This model is used to analyse the heat transfer between buried vertical pipes and the ground, and determine the ground thermal properties together with parameters estimation method. The ground thermal conductivity of an actual project was measured and the analysis shows that the results can be used for engineering design.


2021 ◽  
Vol 3 (1) ◽  
pp. 19-28
Author(s):  
Shirin Ghatrehsamani ◽  
Yiannis Ampatzidis ◽  
John K. Schueller ◽  
Reza Ehsani

Heat treatment has been applied in previous studies to treat diseased plants and trees affected by heat-sensitive pathogens. Huanglongbing (HLB) is a heat-sensitive pathogen and the optimal temperature–time for treating HLB-affected citrus trees was estimated to be 54 °C for 60 to 120 s from indoor experimental studies. However, utilizing this method in orchards is difficult due to technical difficulties to effectively apply heat. Recently, a mobile thermotherapy system (MTS) was developed to in-field treat HLB-affected trees. This mobile device includes a canopy cover that covers the diseased tree and a system to supply steam under the cover to treat the tree. It was proven that the temperature inside the canopy cover can reach the desired one (i.e., 54 °C) to kill bacteria. However, for HLB, the heat should penetrate the tree’s phloem where the bacteria live. Therefore, measuring the heat penetration inside the tree is very critical to evaluate the performance of the MTS. In this study, a heat transfer model was developed to simulate the heat penetration inside the tree and predict the temperature in the phloem of the diseased tree during the in-field heat treatment. The simulation results were compared with in-field experimental measurements. The heat transfer model was developed by a comparative analysis of the experimental data using the ANSYS software. Results showed that the temperature in the phloem was 10–40% lower than the temperature near the surface of the bark. Simulation results were consistent with experimental results, with an average relative error of less than 5%.


2019 ◽  
Vol 90 (13-14) ◽  
pp. 1549-1557
Author(s):  
Qian Zhang ◽  
Zhenrong Zheng ◽  
Kezhu Mao ◽  
Wei Zhi ◽  
Lijuan Luo ◽  
...  

In order to predict the thermal insulation performance of coated carbon fiber fabric, a numerical heat transfer model under high temperature was established. The simulation results were validated by quartz lamp ablation experiment. The experimental values were in agreement with the numerical values, and the average relative error between them was 9.47%. Furthermore, the impact of structural parameters on the thermal insulation of coated carbon fiber fabrics, by using the numerical heat transfer model, was investigated. The results show that thermal insulation for the samples is in the order of plain < 2/1 twill < 3/3 twill < 5/3 stain, when using constant structure density and yarn fineness. Thermal insulation performance of the samples dramatically increases as yarn fineness goes from 3 to 12 K. Furthermore, when the structure density increases to more than 70 ends/10 cm, the thermal insulation property shows an increasing trend.


Solar Energy ◽  
2017 ◽  
Vol 153 ◽  
pp. 366-378 ◽  
Author(s):  
Pierre-Luc Paradis ◽  
Daniel R. Rousse ◽  
Louis Lamarche ◽  
Hakim Nesreddine

Sign in / Sign up

Export Citation Format

Share Document