Calculating molten-salt central-receiver lifetime under creep-fatigue damage

Solar Energy ◽  
2021 ◽  
Vol 213 ◽  
pp. 180-197
Author(s):  
P.A. González-Gómez ◽  
M.R. Rodríguez-Sánchez ◽  
M. Laporte-Azcué ◽  
D. Santana
Keyword(s):  
Molten Salt ◽  
Fatigue Damage ◽  
Central Receiver ◽  
Creep Fatigue

Structural Evaluation With Elastic and Inelastic Analysis Methods on a High Temperature Storage Tank Subjected to Static and Dynamic Loadings

2020 ◽  
Author(s):  
Wen Wang ◽  
Xiaochun Zhang ◽  
Xiaoyan Wang ◽  
Maoyuan Cai
Keyword(s):  
High Temperature ◽  
Elevated Temperature ◽  
Molten Salt ◽  
Fatigue Damage ◽  
Storage Tank ◽  
Power Plants ◽  
Elastic Analysis ◽  
Inelastic Analysis ◽  
Analysis Methods ◽  
Creep Fatigue

Abstract The structural integrity of reactor components is very essential for the reliable operation of all types of power plants, especially for components operating at elevated temperature where creep effects are significant and where components are subjected to high-temperature alteration and seismic transient loading conditions. In this article, a molten salt storage tank in high temperature thorium molten salt reactor (TMSR) is evaluated according to ASME-III-5-HBB high temperature reactor code. The evaluation based on 3D finite element analyses includes the load-controlled stress, the effects of ratcheting, and the interaction of creep and fatigue. The thermal and structural analysis and the application procedures of ASME-HBB rules are described in detail. Some structural modifications have been made on this molten salt storage tank to enhance the strength and reduce thermal stress. The effects of ratcheting and creep-fatigue damage under elevated temperature are investigated using elastic analysis and inelastic analysis methods for a defined representative load cycle. In addition, the strain range and the stress relaxation history calculated by elastic and inelastic methods are compared and discussed. The numerical results indicate that the elastic analysis is conservative for design and a full inelastic analysis method for estimating input for creep-fatigue damage evaluation need to be developed.

Central Receiver System Solar Power Plant Using Molten Salt as Heat Transfer Fluid

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
J. Ignacio Ortega ◽  
J. Ignacio Burgaleta ◽  
Félix M. Téllez
Keyword(s):  
Heat Transfer ◽  
Power Generation ◽  
Molten Salt ◽  
Thermal Power ◽  
Solar Thermal ◽  
Heat Transfer Fluid ◽  
Solar Thermal Power ◽  
Central Receiver ◽  
Spanish Legislation ◽  
Solar Thermal Power Generation

Of all the technologies being developed for solar thermal power generation, central receiver systems (CRSs) are able to work at the highest temperatures and to achieve higher efficiencies in electricity production. The combination of this concept and the choice of molten salts as the heat transfer fluid, in both the receiver and heat storage, enables solar collection to be decoupled from electricity generation better than water∕steam systems, yielding high capacity factors with solar-only or low hybridization ratios. These advantages, along with the benefits of Spanish legislation on solar energy, moved SENER to promote the 17MWe Solar TRES plant. It will be the first commercial CRS plant with molten-salt storage and will help consolidate this technology for future higher-capacity plants. This paper describes the basic concept developed in this demonstration project, reviewing the experience accumulated in the previous Solar TWO project, and present design innovations, as a consequence of the development work performed by SENER and CIEMAT and of the technical conditions imposed by Spanish legislation on solar thermal power generation.

Creep-fatigue interaction on estimation of lifetime and fatigue damage of F82H

2021 ◽  
Vol 173 ◽  
pp. 112830
Author(s):  
Wenhai Guan ◽  
Hyoseong Gwon ◽  
Takanori Hirose ◽  
Hisashi Tanigawa ◽  
Yoshinori Kawamura ◽  
...  
Keyword(s):  
Fatigue Damage ◽  
Creep Fatigue

Management of Complex Loading Histories for Use in Probabilistic Creep-Fatigue Damage Assessments

2018 ◽  
Author(s):  
N. A. Zentuti ◽  
J. D. Booker ◽  
R. A. W. Bradford ◽  
C. E. Truman
Keyword(s):  
Fatigue Damage ◽  
Input Parameter ◽  
Three Dimensional ◽  
Complex Loading ◽  
Fe Model ◽  
Plant Component ◽  
Fatigue Lifetime ◽  
Wide Range ◽  
Stress Components ◽  
Creep Fatigue

An approach is outlined for the treatment of stresses in complex three-dimensional components for the purpose of conducting probabilistic creep-fatigue lifetime assessments. For conventional deterministic assessments, the stress state in a plant component is found using thermal and mechanical (elastic) finite element (FE) models. Key inputs are typically steam temperatures and pressures, with the three principal stress components (PSCs) at the assessment location(s) being the outputs. This paper presents an approach which was developed based on application experience with a tube-plate ligament (TPL) component, for which historical data was available. Though both transient as well as steady-state conditions can have large contributions towards the creep-fatigue damage, this work is mainly concerned with the latter. In a probabilistic assessment, the aim of this approach is to replace time intensive FE runs with a predictive model to approximate stresses at various assessment locations. This is achieved by firstly modelling a wide range of typical loading conditions using FE models to obtain the desire stresses. Based on the results from these FE runs, a probability map is produced and input(s)-output(s) functions are fitted (either using a Response Surface Method or Linear Regression). These models are thereafter used to predict stresses as functions of the input parameter(s) directly. This mitigates running an FE model for every probabilistic trial (of which there typically may be more than 104), an approach which would be computationally prohibitive.

A Direct Method on the Evaluation of Cyclic Steady State of Structures With Creep Effect

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Haofeng Chen ◽  
Weihang Chen ◽  
James Ure
Keyword(s):  
Fatigue Damage ◽  
Mechanical Load ◽  
Direct Method ◽  
Load Condition ◽  
Hysteresis Loops ◽  
Strain Range ◽  
Cyclic Behavior ◽  
Direct Evaluation ◽  
Plastic Strain Range ◽  
Creep Fatigue

This paper describes a new extension of the linear matching method (LMM) for the direct evaluation of cyclic behavior with creep effects of structures subjected to a general load condition in the steady cyclic state, with the new implementation of the cyclic hardening model and time hardening creep constitutive model. A benchmark example of a Bree cylinder and a more complicated three-dimensional (3D) plate with a center hole subjected to cyclic thermal load and constant mechanical load are analyzed to verify the applicability of the new LMM to deal with the creep fatigue damage. For both examples, the stabilized cyclic responses for different loading conditions and dwell time periods are obtained and validated. The effects of creep behavior on the cyclic responses are investigated. The new LMM procedure provides a general purpose technique, which is able to generate both the closed and nonclosed hysteresis loops depending upon the applied load condition, providing details of creep strain and plastic strain range for creep and fatigue damage assessments with creep fatigue interaction.

The Mechanical Interaction of Clad and Base Metal for Molten Salt Reactor Structural Components

2018 ◽  
Author(s):  
M. C. Messner ◽  
V.-T. Phan ◽  
R. I. Jetter ◽  
T.-L. Sham
Keyword(s):  
High Temperature ◽  
Molten Salt ◽  
Mechanical Response ◽  
Base System ◽  
Molten Salt Reactor ◽  
Structural Components ◽  
Mechanical Interaction ◽  
Base Materials ◽  
Creep Fatigue ◽  
Axisymmetric Structures

Cladding structural components with a corrosion resistant material may greatly extend the design life of molten salt reactor concepts. A complete design methodology for such cladded, high temperature nuclear components will require addressing many issues: fabrication, corrosion resistance, metallurgical interaction, and the mechanical interaction of the clad and base materials under load. This work focuses on the final issue: the mechanical interaction of the base and clad under creep-fatigue conditions. Depending on the relative mechanical properties of the two materials the clad may substantially influence the long-term cyclic response of the structural system or its effect might be negligible. To quantify the effect of different clad material properties we develop an efficient method for simulating pressurized cladded components in the limiting case where the section of interest is far from structural discontinuities. Using this method we evaluate the mechanics of the clad/base system and identify different regimes of mechanical response. The focus is on situations relevant to high temperature nuclear components: thermal-cyclic Bree-type problems and similar axisymmetric structures. The insights gained from these structural studies will form the basis for developing design rules for high-temperature, nuclear, cladded components.

Sign in / Sign up

Export Citation Format

Share Document