Circuit board integrated patch transition between microstrip and rectangular waveguide, optimised for producibility

2006 ◽  
Vol 153 (4) ◽  
pp. 330 ◽  
Author(s):  
P. Hallbjörner
Keyword(s):  
Rectangular Waveguide ◽  
Circuit Board

A Novel Wideband transition from Substrate Integrated Waveguide to Rectangular Waveguide

2020 ◽  
Vol 10 ◽  
Author(s):  
Keyur Mahant ◽  
Hiren Mewada ◽  
Amit Patel ◽  
Alpesh Vala ◽  
Jitendra Chaudhari
Keyword(s):  
Rectangular Waveguide ◽  
Printed Circuit Board ◽  
Low Cost ◽  
Single Layer ◽  
Circuit Board ◽  
Substrate Integrated Waveguide ◽  
Ka Band ◽  
Better Than ◽  
Millimeter Wave Circuits ◽  
Wideband Transition

Aim: In this article, wideband substrate integrated waveguide (SIW) and rectangular waveguide (RWG) transition operating in Ka-band is proposed Objective: In this article, wideband substrate integrated waveguide (SIW) and rectangular waveguide (RWG) transition operating in Ka-band is proposed. Method: Coupling patch etched on the SIW cavity to couple the electromagnetic energy from SIW to RWG. Moreover, metasurface is introduced into the radiating patch to enhance bandwidth. To verify the functionality of the proposed structure back to back transition is designed and fabricated on a single layer substrate using standard printed circuit board (PCB) fabrication technology. Results: Measured results matches with the simulation results, measured insertion loss is less than 1.2 dB and return loss is better than 3 dB for the frequency range of 28.8 to 36.3 GHz. By fabricating transition with 35 SRRs bandwidth of the proposed transition can be improved. Conclusion: The proposed transition has advantages like compact in size, easy to fabricate, low cost and wide bandwidth. Proposed structure is a good candidate for millimeter wave circuits and systems.

Circuit Board Device

2020 ◽  
Author(s):  
Keyword(s):  
Circuit Board

406. An Ergonomic Hazards Survey of Printed Circuit Board Factories

1999 ◽  
Author(s):  
C. Lu ◽  
S. Wang ◽  
C. Wei ◽  
S. In
Keyword(s):  
Printed Circuit Board ◽  
Circuit Board ◽  
Printed Circuit

Characteristics of Radiated Emission from a Printed Circuit Board with a Slit

2012 ◽  
Vol 132 (6) ◽  
pp. 404-410 ◽  
Author(s):  
Kenichi Nakayama ◽  
Kenichi Kagoshima ◽  
Shigeki Takeda
Keyword(s):  
Printed Circuit Board ◽  
Circuit Board ◽  
Printed Circuit ◽  
Radiated Emission

Development of High Permeability Core Materials for Embeddable Inductors in Flexible Organic Substrates

2003 ◽  
Vol 769 ◽  
Author(s):  
C. K. Liu ◽  
P. L. Cheng ◽  
S. Y. Y. Leung ◽  
T. W. Law ◽  
D. C. C. Lam
Keyword(s):  
Low Temperature ◽  
Sol Gel ◽  
Circuit Board ◽  
Organic Substrates ◽  
Circuit Boards ◽  
High Permeability ◽  
Electrical Measurements ◽  
Different Temperatures ◽  
Spiral Inductors ◽  
Ceramic Tape

AbstractCapacitors, resistors and inductors are surface mounted components on circuit boards, which occupy up to 70% of the circuit board area. For selected applications, these passives are packaged inside green ceramic tape substrates and sintered at temperatures over 700°C in a co-fired process. These high temperature processes are incompatible with organic substrates, and low temperature processes are needed if passives are to be embedded into organic substrates. A new high permeability dual-phase Nickel Zinc Ferrite (DP NZF) core fabricated using a low temperature sol-gel route was developed for use in embedded inductors in organic substrates. Crystalline NZF powder was added to the sol-gel precursor of NZF. The solution was deposited onto the substrates as thin films and heat-treated at different temperatures. The changes in the microstructures were characterized using XRD and SEM. Results showed that addition of NZF powder induced low temperature transformation of the sol-gel NZF phase to high permeability phase at 250°C, which is approximately 350°C lower than transformation temperature for pure NZF sol gel films. Electrical measurements of DP NZF cored two-layered spiral inductors indicated that the inductance increased by three times compared to inductors without the DP NZF cores. From microstructural observations, the increase is correlated with the changes in microstructural connectivity of the powder phase.

Ultra-Small Reader/Writer with Multiple Contactless Interfaces on a Flexible Circuit Board

2009 ◽  
Vol E92-B (9) ◽  
pp. 2992-2995
Author(s):  
Hideaki YAMAMOTO ◽  
Minoru IKEDA ◽  
Yasuhiro HOSODA
Keyword(s):  
Circuit Board
Sign in / Sign up

Export Citation Format

Share Document