scholarly journals Continuous dynamic recrystallization during hot torsion of an aluminum alloy.

2019 ◽  
Vol 1270 ◽  
pp. 012049 ◽  
Author(s):  
M C Poletti ◽  
T Simonet-Fotso ◽  
D Halici ◽  
D Canelo-Yubero ◽  
F Montheillet ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Dynamic Recrystallization ◽  
Continuous Dynamic Recrystallization ◽  
Hot Torsion ◽  
Continuous Dynamic

scholarly journals In-situ characterization of continuous dynamic recrystallization during hot torsion of an Al–Si–Mg alloy

2020 ◽  
Vol 822 ◽  
pp. 153282 ◽  
Author(s):  
David Canelo-Yubero ◽  
Zsolt Kovács ◽  
J.F. Thierry Simonet Fotso ◽  
Domonkos Tolnai ◽  
Norbert Schell ◽  
...  
Keyword(s):  
Dynamic Recrystallization ◽  
Mg Alloy ◽  
In Situ Characterization ◽  
Continuous Dynamic Recrystallization ◽  
Hot Torsion ◽  
Continuous Dynamic

Analysis of Large Strain Hot Torsion Textures Associated With “Continuous” Dynamic Recrystallization

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
S. M. Lim ◽  
C. Desrayaud ◽  
F. Montheillet
Keyword(s):  
Grain Boundary ◽  
Dynamic Recrystallization ◽  
Large Strain ◽  
Texture Evolution ◽  
Boundary Migration ◽  
Grain Boundary Migration ◽  
Shear Direction ◽  
Continuous Dynamic Recrystallization ◽  
Hot Torsion ◽  
Continuous Dynamic

The development of ideal orientations within the steady-state region of hot torsion flow curves of fcc and bcc metals undergoing “continuous” dynamic recrystallization is analyzed. It is well known that in fcc metals, e.g., Al deformed at 400°C and above, the experimentally observed end texture consists of the twin-symmetric B(112¯)[11¯0]/B¯(1¯1¯2)[1¯10] component, whereby the (hkl)[uvw] indices correspond to the shear plane z and the shear direction θ, respectively. In bcc iron however, only one of the self-symmetric D1(112¯)[111] and D2(1¯1¯2)[111] components dominates (the former in the case of positive shear or clockwise rotation about the r-axis, and the latter during negative shear). The tendency toward a single end orientation imposes certain limitations on grain refinement, as this would ultimately imply the coalescence of subgrains of or close to this orientation, and therefore the disappearance of existing high angle boundaries (≥15 deg). It is believed that the preference of D1 over D2, or vice versa, could be related to phenomena other than glide-induced rotations, e.g., grain boundary migration resulting from differences in work hardening rates. In this paper, the standard Taylor model is first used to predict the texture evolution in simple shear under the full-constraint rate-sensitive scheme. This is then coupled with an approach that takes into account grain boundary migration resulting from differences in dislocation densities within grains of varying orientations. The preliminary results are in agreement with experimental findings, i.e., grains with initial orientations close to D2 grow at the expense of neighboring grains during negative shear and vice versa.

Dynamic Recrystallization Mechanisms of Nickel Niobium Alloys during Hot Working

2021 ◽  
Vol 1016 ◽  
pp. 869-874
Author(s):  
Nadjoua Matougui ◽  
Mohamed Lamine Fares ◽  
David Piot
Keyword(s):  
Dynamic Recrystallization ◽  
Torsion Test ◽  
Large Strains ◽  
Strain Rates ◽  
Niobium Alloys ◽  
Continuous Dynamic Recrystallization ◽  
Hot Torsion ◽  
Hot Torsion Test ◽  
Continuous Dynamic ◽  
Electron Back Scattered Diffraction

This present work examines the influence of niobium in solid solution on the microstructural evolution of pure nickel at various deformation conditions. On this purpose, high-purity nickel and six model nickel-niobium alloys (Ni–0.01, 0.1, 1, 2, 5 and 10 wt. % Nb) were subjected to hot torsion test to large strains within the temperature range from 800 to 1000 °C at strain rates of 0.03, 0.1 and 0.3 s–1. Microstructural analyses were carried out using both optical and scanning electron microscopy-based electron back-scattered diffraction technique. The overall results showed the key role played by the Nb amount when coupled with various DRX mechanisms involved, i.e. DDRX, CDRX, and GDRX with respect to the prescribed deformation conditions, in reducing grain size and retarding DRX kinetics from which the microstructures of the examined materials such as Ni 2 and 10 wt. % Nb were seen evolving in different ways. In all these deformed materials, a transition from discontinuous dynamic recrystallization to continuous dynamic recrystallization was observed at low temperature and high strain rate whereas only discontinuous dynamic recrystallization occurred at high temperature.

Effect of Initial Grain Size on the Dynamic Recrystallization Behaviours of Austenite

2007 ◽  
Vol 561-565 ◽  
pp. 33-36 ◽  
Author(s):  
A. Dehghan-Manshadi ◽  
Peter D. Hodgson
Keyword(s):  
Grain Size ◽  
Dynamic Recrystallization ◽  
Considerable Effect ◽  
Continuous Dynamic Recrystallization ◽  
304 Austenitic Stainless Steel ◽  
Moderate Effect ◽  
Hot Torsion ◽  
Continuous Dynamic ◽  
Critical Strains ◽  
Type 304

The effect of initial grain size on the recrystallization behaviour of a type 304 austenitic stainless steel was investigated using hot torsion. Refinement of the initial grain size to 8 μm had a considerable effect on the flow curve shapes, peak and critical strains and also on DRX kinetics, compared with an initial grain size of 35 μm. Microstructural investigations using EBSD suggest a transition from conventional (discontinuous) to continuous dynamic recrystallization with decreasing initial grain size. Also, there was a moderate effect of initial grain size on the DRX grain size.

Sign in / Sign up

Export Citation Format

Share Document