An investigation of microstructure, wear and corrosion resistance of AZ31B–SiO2–graphite hybrid surface composite produced by friction stir processing

2020 ◽  
Vol 6 (12) ◽  
pp. 1250a7
Author(s):  
M Rezaeian-delouei ◽  
H Abdollah-Pour ◽  
M Tajally ◽  
S M Mousavizade
Keyword(s):  
Corrosion Resistance ◽  
Friction Stir Processing ◽  
Friction Stir ◽  
Surface Composite ◽  
Wear And Corrosion ◽  
Wear And Corrosion Resistance

scholarly journals Effect of III-Pass on Microstructure, Micro Hardness and Static Immersion Corrosion Resistance of AA6061-T6/SiCp Surface Composite Fabricated by Friction Stir Processing

2012 ◽  
pp. 152-156
Author(s):  
Devaraju Aruri ◽  
Adepu Kumar ◽  
B Kotiveerachary
Keyword(s):  
Corrosion Resistance ◽  
Friction Stir Processing ◽  
Stir Zone ◽  
Al Alloy ◽  
Micro Hardness ◽  
Friction Stir ◽  
Surface Composite ◽  
Sic Particles ◽  
Immersion Corrosion ◽  
Static Immersion

In this current investigation, SiC particles 20μm in average size were incorporated into the commercially AA6061-T6 to prepare surface composite by using Friction stir processing (FSP). The morphology of the reinforcement inside the Al matrix has been evaluated from scanning electron microscope (SEM) and the corrosion characteristics of the resulted composite were evaluated using static immersion corrosion (SIC) behavior in 3.5% NaCl aqueous solution at various regimes. From the results, it observed that the SiC particles were distributed uniformly inside the stir zone (SZ) in both first and third-pass of FSP. The micro hardness of stir zone with SiC particles of I-pass was higher compared to III-pass and as-received Al alloy. In static immersion corrosion test the FSP AA6061-T6/SiCp exhibited significantly greater corrosion resistance in I-pass than compared to the III-pass and as-received Al alloy.

Evaluation of wear and corrosion resistance of pure Mg wire produced by friction stir extrusion

2015 ◽  
Vol 25 (6) ◽  
pp. 1847-1855 ◽  
Author(s):  
Mohammad SHARIFZADEH ◽  
Mohammad ali ANSARI ◽  
Morteza NARVAN ◽  
Reza ABDI BEHNAGH ◽  
Alireza ARAEE ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Friction Stir ◽  
Wear And Corrosion ◽  
Friction Stir Extrusion ◽  
Wear And Corrosion Resistance

TANTUNG G

Alloy Digest ◽  
1961 ◽  
Vol 10 (7) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Cutting Tools ◽  
Heat Treating ◽  
Nonferrous Alloy ◽  
Wear And Corrosion ◽  
Wear And Corrosion Resistance

Abstract TANTUNG G is a cast nonferrous alloy containing tantalum or columbium carbide and having wear and corrosion resistance. It is used primarily for cutting tools. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on forming, heat treating, machining, and joining. Filing Code: Co-28. Producer or source: Vascoloy, Ramet Division.

ALLEGHENY LUDLUM TYPE 420

Alloy Digest ◽  
2000 ◽  
Vol 49 (8) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Wear And Corrosion ◽  
Wear And Corrosion Resistance ◽  
Chromium Stainless Steel

Abstract Allegheny Ludlum Type 420 is a hardenable, straight-chromium stainless steel with wear and corrosion resistance. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and machining. Filing Code: SS-801. Producer or source: Allegheny Ludlum Corporation.

Sign in / Sign up

Export Citation Format

Share Document