A Minimum Power Circulating Flow and Optimal Dead-time Control Method for GaN Based DAB Converter with EPS Control

2021 ◽  
Author(s):  
ChengZi Yang ◽  
Haoyuan Jin ◽  
Huaqing Li ◽  
Longyang Yu ◽  
Yunqing Pei ◽  
...  
Keyword(s):  
Dead Time ◽  
Control Method ◽  
Minimum Power ◽  
Time Control

Optimized Non-Dead-Time Control of Inverter with Two-Phase Modulated SVPWM

2012 ◽  
Vol 562-564 ◽  
pp. 1531-1536
Author(s):  
Ming Xing Zhu ◽  
Jing Bo Shi
Keyword(s):  
Control Strategy ◽  
Pulse Width Modulation ◽  
Dead Time ◽  
Control Method ◽  
Short Circuit ◽  
Two Phase ◽  
Zero Crossing ◽  
Time Control ◽  
Bus Voltage ◽  
Current Zero

In the inverter control system, two-phase modulated space vector pulse width modulation (SVPWM) algorithm has the advantages of minimum switch loss and higher utilization of direct current (DC) bus voltage. Non-dead-time control strategy can eliminate the problems of the dead time effects. But the traditional non-dead-time control strategy heavily depends on the current zero-crossing detection, which may cause the output voltage distortion or even a short circuit. Based on the analysis of the reason for the distortion, a new optimized non-dead-time control method is proposed. Two methods for the detection of the overlapping area are enumerated. The conclusions are confirmed by the simulation results with MATLAB/ SIMULINK.

A Novel Dead-Time Control Method for Double End Converter

2014 ◽  
Vol 571-572 ◽  
pp. 897-900
Author(s):  
Shu Lin Liu ◽  
Li Li Qi
Keyword(s):  
Experimental Research ◽  
Pulse Width ◽  
Dead Time ◽  
Control Method ◽  
Adjustment Process ◽  
The Novel ◽  
Magnetic Bias ◽  
Time Control ◽  
Pulse Width Modulator ◽  
Drive Signals

In order to achieve symmetry of the drive signal and suppress the magnetic bias, a novel dead-time control method for the double end converter is put forward in this paper, which can generate two independent and complementary PWM waveforms by configuring EPWM (Enhanced Pulse Width Modulator) module. The magnetic bias problems of the double end converter, principle of EPWM module and adjustment process of the dead-time control method are analyzed. Two different dead-times can de realized by setting the rising edge delay and falling edge delay of the corresponding registers in Dead-band (DB) module in one cycle to meet the requirement of drive signals. Experimental research on the novel dead-time control method is done on the push-pull forward circuit and the experiment results verify the feasibility of the proposed method.

scholarly journals A Current-Mode Four-Phase Synchronous Buck Converter with Dynamic Dead-Time Control

IEEE Access ◽  
2021 ◽  
pp. 1-1
Author(s):  
Jun Tang ◽  
Tian Guo ◽  
Jung Sik Kim ◽  
Jeongjin Roh
Keyword(s):  
Dead Time ◽  
Current Mode ◽  
Buck Converter ◽  
Time Control ◽  
A Current

scholarly journals Stacked Buck Converter: Current Ripple Elimination Effect and Transient Response

Energies ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 64
Author(s):  
Chien-Chun Huang ◽  
Yu-Chen Liu ◽  
Chia-Ching Lin ◽  
Chih-Yu Ni ◽  
Huang-Jen Chiu
Keyword(s):  
Transient Response ◽  
Dead Time ◽  
Control Method ◽  
Buck Converter ◽  
Modulation Method ◽  
Output Current ◽  
Time Modulation ◽  
Advantages And Disadvantages ◽  
Improvement Method ◽  
Current Ripple

To balance the cost and volume when applying a low output current ripple, the power supply design should be able to eliminate the current ripple under any duty cycle in medium and high switching frequencies, and considerably reduce filter volume to improve power density. A stacked buck converter was eventually selected after reviewing the existing solutions and discussing their advantages and disadvantages. A stacked buck converter is used as a basis to propose the transient response and output current ripple elimination effect, boundary limit control method, and low output ripple dead time modulation method to make individual improvements. The principle, mathematical derivation, small-signal model, and compensator design method of the improvement method are presented in detail. Moreover, simulation results are used to mutually verify the correctness and effectiveness of the improvement method. A stacked buck converter with 330-V input, 50-V output, and 1-kW output power was implemented to verify the effect of the low output current ripple dead time modulation. Experimental results showed that the peak-to-peak value of the output current ripple was reduced from 2.09 A to 559 mA, and the RMS value was reduced from 551 mA to 91 mA, thereby effectively improving the output current ripple.

Theory of Temperature Dynamic Control in Arch Dams and its Application

2012 ◽  
Vol 594-597 ◽  
pp. 738-741 ◽  
Author(s):  
Yin Duan ◽  
Xing Hong Liu ◽  
Xiao Lin Chang
Keyword(s):  
Real Time ◽  
Temperature Control ◽  
Control Method ◽  
Dynamic Control ◽  
Arch Dam ◽  
Real Time Control ◽  
New Techniques ◽  
Time Dynamic ◽  
Arch Dams ◽  
Time Control

Main factors of the temperature control and crack prevention in arch dams are summarized. The Space-time Dynamic Control method in pipe cooling process and the Temperature Real-time Control and Decision Database System are introduced to help for temperature real-time control and rapid analysis. Successful application of these new techniques in the construction of Dagangshan arch dam indicates that the proposed method are of significant effectiveness on the temperature control and crack prevention, and have good application prospect in practical project.

Sign in / Sign up

Export Citation Format

Share Document