The Effect of Tip Clearance on a Swept Transonic Compressor Rotor

1996 ◽  
Vol 118 (2) ◽  
pp. 230-239 ◽  
Author(s):  
W. W. Copenhaver ◽  
E. R. Mayhew ◽  
C. Hah ◽  
A. R. Wadia
Keyword(s):  
Turbulence Modeling ◽  
Three Dimensional ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Rotor Aerodynamics ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Fan ◽  
Refined Grid

An experimental and numerical investigation of detailed tip clearance flow structures and their effects on the aerodynamic performance of a modern low-aspect-ratio, high-throughflow, axial transonic fan is presented. Rotor flow fields were investigated at two clearance levels experimentally, at tip clearance to tip blade chord ratios of 0.27 and 1.87 percent, and at four clearance levels numerically, at ratios of zero, 0.27, 1.0, and 1.87 percent. The numerical method seems to calculate the rotor aerodynamics well, with some disagreement in loss calculation, which might be improved with improved turbulence modeling and a further refined grid. Both the experimental and the numerical results indicate that the performance of this class of rotors is dominated by the tip clearance flows. Rotor efficiency drops six points when the tip clearance is increased from 0.27 to 1.87 percent, and flow range decreases about 30 percent. No optimum clearance size for the present rotor was indicated. Most of the efficiency change occurs near the tip section, with the interaction between the tip clearance flow and the passage shock becoming much stronger when the tip clearance is increased. In all cases, the shock structure was three dimensional and swept, with the shock becoming normal to the endwall near the shroud.

The Effect of Tip Clearance on a Swept Transonic Compressor Rotor

1994 ◽  
Author(s):  
William W. Copenhaver ◽  
Ellen R. Mayhew ◽  
Chunill Hah
Keyword(s):  
Turbulence Modeling ◽  
Three Dimensional ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Rotor Aerodynamics ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Through Flow ◽  
Clearance Flow ◽  
Transonic Fan

An experimental and numerical investigation of detailed tip clearance flow structures and their effects on the aerodynamic performance of a modern low-aspect-ratio, high-through-flow, axial transonic fan is presented. Rotor flow fields were investigated at two clearance levels experimentally, at tip clearance to tip blade chord ratios of 0.27 and 1.87 percent, and at four clearance levels numerically, at ratios of zero, 0.27, 1.0, and 1.87 percent. The numerical method seems to calculate the rotor aerodynamics well, with some disagreement in loss calculation which might be improved with improved turbulence modeling and a further refined grid. Both the experimental and the numerical results indicate that the performance of this class of rotors is dominated by the tip clearance flows. Rotor efficiency drops six points when the tip clearance is increased from 0.27 to 1.87 percent, and flow range decreases about 30 percent. No optimum clearance size for the present rotor was indicated. Most of the efficiency change occurs near the tip section, with the interaction between the tip clearance flow and the passage shock becoming much stronger when the tip clearance is increased. In all cases, the shock structure was three-dimensional and swept, with the shock becoming normal to the endwall near the shroud.

Effect of tip clearance size on the performance of a low-reaction transonic axial compressor rotor

2019 ◽  
Vol 234 (2) ◽  
pp. 127-142
Author(s):  
Wei Zhu ◽  
Songtao Wang ◽  
Longxin Zhang ◽  
Jun Ding ◽  
Zhongqi Wang
Keyword(s):  
Numerical Simulations ◽  
Dynamic Balance ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Phenomena

This study aimed to enhance the understanding of flow phenomena in low-reaction aspirated compressors. Three-dimensional, multi-passage steady and unsteady numerical simulations are performed to investigate the performance sensitivity to tip clearance variation on the first-stage rotor of a multistage low-reaction aspirated compressor. Three kinds of tip clearance sizes including 1.0τ, 2.0τ and 3.0τ are modeled, in which 1.0τ corresponds to the designed tip clearance size of 0.2 mm. The steady numerical simulations show that the overall performance of the rotor moves toward lower mass flow rate when the tip clearance size is increased. Moreover, energy losses, efficiency reduction and stall margin decrease are also observed with increasing tip clearance size. This can be mostly attributed to the damaging impact of intense tip clearance flow. For unsteady simulation, the result shows periodical oscillation of the tip leakage vortex and a “two-passage periodic structure” in the tip region at the near-stall point. The occurrence of the periodical oscillation is due to the severe interaction between the tip clearance flow and the shock wave. However, the rotor operating state is still stable at this working point because a dynamic balance is established between the tip clearance flow and incoming flow.

Three-Dimensional Flowfields Inside a Transonic Compressor With Swept Blades

1991 ◽  
Vol 113 (2) ◽  
pp. 241-250 ◽  
Author(s):  
C. Hah ◽  
A. J. Wennerstrom
Keyword(s):  
Turbulence Modeling ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Tip Clearance Flow ◽  
Transonic Compressor ◽  
Improved Performance

The concept of swept blades for a transonic or supersonic compressor was reconsidered by Wennerstrom in the early 1980s. Several transonic rotors designed with swept blades have shown very good aerodynamic efficiency. The improved performance of the rotor is believed to be due to reduced shock strength near the shroud and better distribution of secondary flows. A three-dimensional flowfield inside a transonic rotor with swept blades is analyzed in detail experimentally and numerically. A Reynolds-averaged Navier–Stokes equation is solved for the flow inside the rotor. The numerical solution is based on a high-order upwinding relaxation scheme, and a two-equation turbulence model with a low Reynolds number modification is used for the turbulence modeling. To predict flows near the shroud properly, the tip-clearance flow also must be properly calculated. The numerical results at three different operating conditions agree well with the available experimental data and reveal various interesting aspects of shock structure inside the rotor.

scholarly journals Three-Dimensional Flowfields Inside a Transonic Compressor With Swept Blades

1990 ◽  
Author(s):  
C. Hah ◽  
A. J. Wennerstrom
Keyword(s):  
Turbulence Modeling ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Tip Clearance Flow ◽  
Transonic Compressor ◽  
Improved Performance

The concept of swept blades for a transonic or supersonic compressor was reconsidered by Wennerstrom in the early 1980s. Several transonic rotors designed with swept blades have shown very good aerodynamic efficiency. The improved performance of the rotor is believed to be due to reduced shock strength near the shroud and better distribution of secondary flows. A three-dimensional flowfield inside a transonic rotor with swept blades is analyzed in detail experimentally and numerically. A Reynolds-averaged Navier-Stokes equation is solved for the flow inside the rotor. The numerical solution is based on a high-order upwinding relaxation scheme, and a two-equation turbulence model with a low Reynolds number modification is used for the turbulence modeling. To properly predict flows near the shroud, the tip-clearance flow also must be properly calculated. The numerical results at three different operating conditions agree well with the available experimental data and reveal various interesting aspects of shock structure inside the rotor.

Characteristics of Tip Clearance Flow Instability in a Transonic Compressor

2010 ◽  
Author(s):  
Chunill Hah ◽  
Melanie Voges ◽  
Martin Mueller ◽  
Heinz-Peter Schiffer
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Flow Instability ◽  
Tip Clearance ◽  
Piv Measurements ◽  
Tip Clearance Flow ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Tip Clearance Vortex

In the present study, unsteady flow phenomena due to tip clearance flow instability in a modern transonic axial compressor rotor are studied in detail. First, unsteady flow characteristics due the oscillating tip clearance vortex measured with the particle image velocimetry (PIV) and casing-mounted unsteady pressure transducers are analyzed and compared to numerical results with a large eddy simulation (LES). Then, measured characteristic frequencies of the unsteady flow near stall operation are investigated. The overall purpose of the study is to advance the current understanding of the unsteady flow field near the blade tip in an axial transonic compressor rotor near the stall operating condition. Flow interaction between the tip leakage vortex and the passage shock is inherently unsteady in a transonic compressor. The currently applied PIV measurements indicate that the flow near the tip region is unsteady even at the design condition. This self-induced unsteadiness increases significantly as the compressor operates toward the stall condition. PIV data show that the tip clearance vortex oscillates substantially near stall. The calculated unsteady characteristics from LES agree well with the PIV measurements. Calculated unsteady flow fields show that the formation of the tip clearance vortex is intermittent and the concept of vortex breakdown from steady flow analysis does not seem to apply in the current flow field. Fluid with low momentum near the pressure side of the blade close to the leading edge periodically spills over into the adjacent blade passage. The spectral analysis of measured end wall and blade surface pressure shows that there are two dominant frequencies near stall. One frequency is about 40–60% of the rotor rotation and the other dominant frequency is about 40–60% of the blade passing frequency (BPF). The first frequency represents the movement of a large blockage over several consecutive blade passages against the rotor rotation. The second frequency represents traditional tip flow instability, which has been widely observed in subsonic compressors. The LES simulations show that the second frequency is due to movement of the instability vortex.

A Numerical Modeling of Endwall and Tip-Clearance Flow of an Isolated Compressor Rotor

1986 ◽  
Vol 108 (1) ◽  
pp. 15-21 ◽  
Author(s):  
C. Hah
Keyword(s):  
Three Dimensional ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Tip Clearance Flow ◽  
Generalized Coordinates ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Phenomena ◽  
Entire Flow

The current study is aimed at developing and appraising a numerical method for the development of endwall boundary layers through tip-clearances and their effect on the performance of an isolated compressor rotor. The Reynolds-averaged Navier-Stokes equation is solved for the entire flow field in elliptic form. The relative flow is computed on the generalized coordinates fixed on the rotor. Comparison between the numerical results and experimental data indicates that the complex three-dimensional viscous flow phenomena inside the tip region are properly predicted.

3-D Digital PIV Measurements of the Tip Clearance Flow in an Axial Compressor

2002 ◽  
Author(s):  
Mark P. Wernet ◽  
Dale Van Zante ◽  
Tony J. Strazisar ◽  
W. Trevor John ◽  
P. Susan Prahst
Keyword(s):  
Three Dimensional ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Image Velocimetry ◽  
Clearance Flow ◽  
Compressor Performance ◽  
Tip Clearance Vortex

The accurate characterization and simulation of rotor tip clearance flows has received much attention in recent years due to their impact on compressor-performance and stability. At NASA Glenn the first known three dimensional Digital Particle Image Velocimetry (DPIV) measurements of the tip region of a low speed compressor rotor have been acquired to characterize the behavior of the rotor tip clearance flow. The measurements were acquired phase-locked to the rotor position so that changes in the tip clearance vortex position relative to the rotor blade can be seen. The DPIV technique allows the magnitude and relative contributions of both the asynchronous motions of a coherent structure and the temporal unsteadiness to be evaluated. Comparison of measurements taken at the peak efficiency and at near stall operating conditions characterizes the mean position of the clearance vortex and the changes in the unsteady behavior of the vortex with blade loading. Comparisons of the 3-D DPIV measurements at the compressor design point to a 3D steady N-S solution are also done to assess the fidelity of steady, single-passage simulations to model an unsteady flow field.

Sign in / Sign up

Export Citation Format

Share Document